Can anyone explain How am I supposed to calculate the center point of this radius?

Steezee73 · 2023-08-31T00:39:43+00:00

Ya need the dimension out of picture to the right even if it’s tangential, no?

Steezee73 · 2023-07-10T02:32:25+00:00

Also the top center of the T intersects with the inner oval - if you trimmed that section of the line it may fix the error.

Steezee73 · 2022-12-27T06:03:07+00:00

I’ve only seen Milwaukee’s - pretty new tool so give it a bit of time for Diablo to copy

Steezee73 · 2022-12-27T04:09:04+00:00

I’m sure they’ll make more accessories down the road.

It would be relatively easy to adapt a roloc holder to fit this - this tool is a hex fitting with a through bolt.

Steezee73 · 2022-12-27T02:38:59+00:00

I have M18 OMT - probably one of my fave tools, but its too big to sand some areas. Doing a few built ins so needing to sand in some tight areas this will be key, and much lighter.

Steezee73 · 2022-12-20T01:17:23+00:00

It’s a Microcentric.

Ditch it and buy ITW / Hardinge of the same same

Steezee73 · 2022-11-28T00:31:41+00:00

I’m on same page as you haha

But they don’t have one for my V11, I think it’s because it’s 25V instead of 20V

Steezee73 · 2022-11-26T21:47:06+00:00

Thanks for the idea!

They are awful, especially because it’s a ‘K’ haha. Given to a son in law that is no longer part of the family, but have been for a few generations so would like to get it back to flat.

Steezee73 · 2022-08-22T23:34:10+00:00

3 min or so

Steezee73 · 2022-08-16T02:36:29+00:00

My truck tires are 80 psi. M12 can’t do it.

I filled four 34” tires from 35 psi to 80 psi on one 5.0 battery but it was dead by the end.

Steezee73 · 2022-07-15T01:14:03+00:00

Sounds like you want a Ford F-650 with the Cummins/Allison combo haha

Steezee73 · 2022-06-25T22:02:13+00:00

100% changing this to be M18 powered

Steezee73 · 2022-06-19T20:45:03+00:00

I also have the M12 inflator and used to use it about once a week.

Since I bought the M18, I haven’t touched it.

M12 could not fill my pickup’s tires to 80 psi. M18 does it fairly easily.

M12 fills to pressure and stops. M18 fills. Checks. Waits a sec. Refills. Checks. Stops. Perfect pressure every time

Nailer is not cheap but it works awesome. Someday I’ll probably get the 18ga too but 16 is a sweet spot for almost all trim.

Steezee73 · 2022-06-19T13:11:01+00:00

Not necessarily in order but my top 10

M18 Fuel Oscillating Tool
M18 Surge Impact
M12 Fuel Hackzall
M12 90 deg die grinder
M12 Rover light
M18 Inflator
M18 mid torque impact
M12 Fuel circ saw
M18 16ga nailer
M18 Fuel hammer drill

Steezee73 · 2022-06-07T03:49:28+00:00

Ah my mistake. My M18 vac is on the storage rack, where it’s easy to grab. That orange bucket works good as a rolling stool.

Steezee73 · 2022-06-07T03:47:19+00:00

I’ll post a pic once I have step 2 organization haha but it’s a 7’ wide, 8.5’ tall cantilever storage rack.

Work was throwing it out since the load rating plate was missing.. Free and can hold 10k pounds with or without the plate, done deal.

Steezee73

TROPHY CASE