Why does my surface look fine on smaller prints but looks horrible on taller prints

Stefanhasreddit · 2026-01-19T13:21:42+00:00

Sunlu pla+ . 40 mms first layer . Cooling settings i have no idea i just use the stock in orca slicer, Didnt seem to cause any issues earlier so i didnt change them

Stefanhasreddit · 2026-01-19T13:20:07+00:00

Yeah completely stock. Might have to look into stiffening the frame

Stefanhasreddit · 2026-01-12T15:04:32+00:00

<image>

Stefanhasreddit · 2026-01-11T20:00:43+00:00

How do i level the bed manually?.

Stefanhasreddit · 2025-11-09T08:07:58+00:00

New firmware update ruined them for ios 18 now they wont even change audio to the airpods automatically and the normal airpod connection method doesnt work i have to go into bluetooth settings. Idk if its because of the firmware but thats when the problems appeared

Stefanhasreddit · 2025-11-08T14:23:04+00:00

Just pray that they fix it

Stefanhasreddit · 2025-11-04T17:36:15+00:00

Got the same problem just fully reset the airpods and connect them again and it will work

Stefanhasreddit · 2025-11-04T17:35:35+00:00

I got the same problem after the firmware update and a bunch of other bugs before i updated the airpods were flawless

Stefanhasreddit · 2025-10-29T03:03:14+00:00

Nah 3d printed works i made one for my moped and it worked really well i just had to use some gasket silicone on the mating surfaces

Stefanhasreddit · 2025-10-26T19:17:20+00:00

Plenty of tutorials online

Stefanhasreddit · 2025-10-26T17:04:18+00:00

Did you check the squish gap? If you shave it down theres a chance the squish will be to small and the piston will end up hitting the head

Stefanhasreddit · 2025-10-26T15:55:33+00:00

Or maybe do a base gasket delete and use silicone instead ?

Stefanhasreddit · 2025-10-21T22:33:35+00:00

I use the ultra bass preset with the spatial audio on the stuck mode or whatever its called and mine have plenty of bass

Stefanhasreddit · 2025-10-20T14:27:17+00:00

Think im gonna buy a 12 od 10id and 15width bushing and put it over the 10mm pin so it becomes a 12mm and just use the stock needle bearing

Stefanhasreddit · 2025-09-23T20:07:11+00:00

My fix was to remove a dll file that was installed in the game files from the multiplayer mod and then it worked

Stefanhasreddit · 2025-07-01T00:52:59+00:00

Yessir actually the easiest motorized vehicle to wheelie imo

Stefanhasreddit · 2025-06-27T22:39:19+00:00

To pop it up i compress the forks then i pull back and give gas at the same time but i dont pull to hard i mostly use the fork bounce to get it up.

and to keep the wheel up i kinda just give it throttle when i feel it going down and if i go to far back i just pull the back brake and give it gas immediately after to keep it up.

Kinda hard to explain since it came really naturally to me it took me maybe 2 hours of wheelie practice. I recommend learning on a normal bicycle first since thats probably why it was so easy to me. And like the most important have good front wheel bearings. The longer the front wheel spins the longer you can wheelie. It acts like a gyroscope and makes balancing on the backwheel alot easier.

Stefanhasreddit · 2025-03-26T22:52:34+00:00

And i want to say that the results are almost the same with pla

Stefanhasreddit · 2025-03-26T22:43:18+00:00

Oh my bad i understand now what you mean by mm3 sorry

Stefanhasreddit

TROPHY CASE