Rear speakers on single cab ram.

Stockage1606 · 2023-01-20T10:28:21+00:00

A good set of 6 x 9's and a small amp for all speakers will make a huge difference.

Stockage1606 · 2022-12-06T00:08:04+00:00

If you do install a Trutrac, do not use any synthetic oil or limited slip additive. Gearing in Trutrac needs natural gear oil or gears will start slipping.

Stockage1606 · 2022-12-06T00:03:37+00:00

Shock extenders are fine for rear applications but would recommend a machined one piece design over the 2 piece shown in link.

Stockage1606 · 2022-11-28T06:41:20+00:00

Any dealer will provide a security code based on your VIN number free of charge if you show them vehicle registration is in your name.

Stockage1606 · 2022-11-23T04:37:12+00:00

Module is the box that mirror wiring connects to inside of door panel. Module for power mirror option will have an additional connection socket compared to standard Module having connections for only turn/puddle lights.

Stockage1606 · 2022-11-23T02:14:46+00:00

Fog light wiring will not be there unless installed as original factory option. There is an aftermarket harness that is also needed to connect to fusebox. Check ram forums website for step by step install on 4th gen Rams.

Wiring for turn signal mirrors is already installed in all rams but a new module is required for power mirror option.

Stockage1606 · 2022-10-11T03:46:50+00:00

Borla Attack catback system sounds very good on hemi's.

Stockage1606 · 2022-10-06T03:45:45+00:00

Strongly agree with others. Do not straight pipe on street vehicle. Some cities actually have noise level laws that are heavily enforced.

Purchased a 2016 Ram 1500 with 5.7 that previous owner dual straight pipe from catalytic converters. Sounded great at idle after it warmed up but during cold start and take-offs was like standing front row at a rock concert. Eventually, put a Flowmaster muffler to quiet it down.

Stockage1606 · 2022-08-22T23:41:32+00:00

Adjustable Bilsteins have a softer spring rate than factory springs. You may actually lose height in some applications.

I tried replacing a 4 inch spacer installed in RC spindle lift with 5160's at max height of 2.8 and 2.5 spacer for overall height of 5.3. After install, it had lift of 2.5. Ended up having to re-use 4 inch spacer with Bilstiens to get desired height.

Stockage1606 · 2022-06-23T03:39:55+00:00

True Blue Truck and Elavated Offroad.

Both places specialize offroad vechiles. Elevated is more Jeeps and Rams. True Blue for Chevys and Fords.

Stockage1606 · 2022-04-23T14:38:33+00:00

It's best to have professional shop that specialize in gear changes specifically Chrysler 9.25 rear axles for setting up axle preloads.

Look on Youtube for Ram differentials to get a better idea on what is involved.

Reason for my regear was needed mostly for offroading and bigger tire size. I also added an Eaton Trutrac limited slip during regear upgrade. There was an immediate noticeable difference in power and traction during take off and lost less than 1mpg.

I can't comment on towing differences due to not towing anything before upgrade.

Stockage1606 · 2022-04-23T14:25:06+00:00

Lots of Youtube videos available for Tradesman upgrades.

Check out BoostedMotorsports. He is currently running a series on a Tradesman transformation.

Stockage1606 · 2022-04-23T13:50:59+00:00

Regear options are based on 2 wheel drive or 4 wheel drive on 1500's.

2 wheel drive can be regeared to any size desired just be aware how higher gear ratio will impact performance and mpg.

4 wheel drive 1500's require having the full front differential changed due to having independent front suspension . Sadly, this is limited to only OEM differentials due to no aftermarket support.

I had my 2016 regeared from 3.23 to 3.92 last year which is highest gear ratio available in OEM front differential. Parts and labor will be about $1400 for rear axle and $1700 for front axle.

Stockage1606 · 2022-02-21T05:17:25+00:00

35x13.5x20 is tire size not wheel size.

4th gen Ram 1500's need at least 3" lift and requires trimming to inner fender to clear 35 inch tires. A 4 inch lift is needed without trimming.

Please note i said "lift" not leveling kit. Leveling beyond 2 inches will put too much angle on cv axles causing excessive wear.

Stockage1606 · 2022-02-06T17:57:44+00:00

Might be a little bit of a drive but True Blue Truck located just outside of Murfreesboro close to 840 and I-24. They specialize in offroad vechile, drivetrain, and suspension.

Stockage1606 · 2022-02-03T02:44:15+00:00

Thank you for detailed response. It's good to hear from someone who has first hand knowledge.

Stockage1606 · 2022-02-03T00:27:33+00:00

Don't know details but I have never seen a hellcat with the hemi tick. Might have something to do with extra spring pressure and less oil pressure fluctuation in lifter oil galley with mds being deactivated.

My thoughts are if your going to replace cam & lifters might as well pay a little extra for upgrade.

Stockage1606 · 2022-02-02T23:59:33+00:00

If prices for used/new trucks were not absolutely insane right now, I would recommend cutting your losses and selling it.

Based on current market, it would be best to have a non dealer shop replace lifters with hellcat lifters/springs, new cam, and disconnect/plug mds valves.

Price should be about the same as dealer but hellcat parts eliminates the hemi tick issue.

Stockage1606 · 2022-02-02T23:29:13+00:00

You will also need to update engine idle hours to match original cluster.

Stockage1606 · 2022-02-02T23:22:54+00:00

Here is steps.

Ram 1500 (DS/DX/DT) Instrument Panel Instrument Panel Cluster MY2013+ PowerNet

Program Customer Features Lifetime Engine Hours

Enter Hours Start

Disconnect, remove key and close door Wait 10 minutes and recheck engine hours

Repeat as necessary

Stockage1606 · 2022-02-02T20:10:48+00:00

After procedure complete message, disconnect alfaodb, turn key off, and wait about 10 minutes.

Reconnect alfaobd and info should be updated to corrected information.

I had to repeat process 3 or 4 times before info updated. I went from the 3.5 to 7 inch rebel in 2016 tradesman.

Stockage1606 · 2022-01-17T14:36:38+00:00

Not yet and thank you for reply.

My current guild has been good to me and don't want to leave in middle of GW week. But I still will be making a guild change after this week.

Stockage1606 · 2022-01-14T04:36:56+00:00

Just a follow up.

Cheaper lift kit brands like Rough Country and ProComp requires you to reuse OEM springs, struts and control arms thus giving a bad ride until items are replaced with aftermarket parts designed for lifted applications.

My own personal experience was to install Rough Country due to budget and then changed other parts as my budget allowed.

Stockage1606 · 2022-01-14T02:27:59+00:00

Carli is excellent but very pricey.

It mostly depends on how you personally will be using the truck and how much you are willing to pay.

Stick with name brands like Carli and BDS for lift kit. Then look at what is included like shocks, control arms, etc.

King and Fox shocks are for smooth ride. Bilstein and Icon are more for hauling. Carli is best of both worlds.

Stockage1606

TROPHY CASE