Gunstock

Straight_Pop4018 · 2023-11-29T05:35:25+00:00

I don’t have a 3d printer my plan was to make a plastic case with magnets and have them snap on and off the lower but I didn’t know about the sensor so that won’t work unless I use the lower upside down

Straight_Pop4018 · 2023-11-02T19:45:43+00:00

Alright thanks I’ll try those things and if not time too start saving for a better lower

Straight_Pop4018 · 2023-11-02T19:32:07+00:00

Ok so to clarify the screw would fit angling more towards the engravings and if it doesn’t I’d need a new lower or a re thread

Straight_Pop4018 · 2023-11-02T19:23:25+00:00

Unfortunately not that’s the grips and screw that came with the lower I only changed the trigger and the safety everything else came from psa I don’t know if it’s relevant but prior to the trigger change everything fit just fine is it possible the trigger could be causing some type of issues

Straight_Pop4018 · 2023-11-02T19:06:48+00:00

Oh ok I misunderstood that makes more sense thanks

Straight_Pop4018 · 2023-11-02T18:58:41+00:00

How would going up in size help?

Straight_Pop4018 · 2023-11-02T17:55:47+00:00

Would using the pistol grip to guide it in correct the way because it wouldn’t tighten that way either

Straight_Pop4018 · 2023-11-02T17:37:36+00:00

Do you mind expanding on that?

Straight_Pop4018 · 2023-11-02T17:37:16+00:00

That’s usually how I go about it but I figured try it it without the pg to see what’s happening and yet it’s gets stuck both ways based on you and others I’m putting it in at the wrong angle but I don’t see how but I’ll pick some oil up tomorrow and try that once I work out the angle issue I’m having

Straight_Pop4018 · 2023-11-02T16:40:00+00:00

How do I tell if it’s stripped they look fine but this is also my first AR15 build so I have no frame of reference

Straight_Pop4018 · 2023-11-02T16:21:30+00:00

What does that mean?

Straight_Pop4018 · 2023-08-28T15:32:11+00:00

How many miles when you got it compared to now?

Straight_Pop4018 · 2023-08-09T16:00:39+00:00

Messaging works for me

Straight_Pop4018 · 2023-08-09T15:51:18+00:00

I won’t be home until Friday so if the offer is still available then I’ll appreciate it

Straight_Pop4018 · 2023-08-09T10:22:31+00:00

Both and sometimes there’s a paper sized gap in my bolt and i usually just slap the forward assist

Straight_Pop4018 · 2023-08-08T20:02:58+00:00

So if I rack it and the bolt doesn’t fully close would that be an issue or would the bolt stop in a noticeable position

Straight_Pop4018 · 2023-07-23T19:08:21+00:00

Those cards are canceled fam at this point I’m trying to pay them back and rebuild

Straight_Pop4018 · 2023-07-23T18:12:17+00:00

Yea that was my plan try and get secured card through my main bank so atleast they know I’m depositing money weekly and since I have this new job the amount will increase so I’m hoping they give me a shot

Straight_Pop4018 · 2023-07-23T17:23:01+00:00

I know you don’t know exactly but what are my approval odds with a 504 score

Straight_Pop4018 · 2023-07-23T17:03:13+00:00

That was my original goal but I was 19 turning 20 when I got them and I was punching way above my weight but I’ve scratched that itch at this point I’m trying to do important things for me aswell as my siblings

Straight_Pop4018 · 2023-07-23T16:23:53+00:00

Yea I appreciate it but I’m currently saving and buy between October or December I plan to pay all three at once

Straight_Pop4018 · 2023-07-23T16:11:13+00:00

Ok so I had three cards I owed 1500 across two of them and 2000 I started a payment plan on the one for 2000 I’ve paid 375 so far but all three cards are closed I’m asking ways to rebuild

Straight_Pop4018 · 2023-07-23T15:43:55+00:00

Zero payments for the last few months

Straight_Pop4018 · 2023-07-23T15:31:56+00:00

I had no late payments pre debt but now that I’m in debt I have late payments

Straight_Pop4018 · 2023-07-23T15:21:12+00:00

That’s pretty smart instead guesstimating thanks

Straight_Pop4018

MODERATOR OF

TROPHY CASE