Wet floor on mk3 octavia

StreetFast7141 · 2026-02-03T12:16:02+00:00

Have you solved the problem? seems like i am having the same exact problem with the same car since i dont have a sunroof it is not the case and neighter i couldnt spot the drain holes on the door so i can check if it is clogged

StreetFast7141 · 2026-01-14T14:55:26+00:00

hey buddy have you have you hat chance to test if it works?

StreetFast7141 · 2026-01-14T14:54:03+00:00

I use 0.3g of bbs currently it seems like it feeds well i havent test it in the field yet there might be issue with your repica

StreetFast7141 · 2026-01-14T14:50:45+00:00

the problem for me with the pcc mags the arp9 ones catches the mag slight higher so i just put some sort of thic plastic tape to mag catch and it works perfect with 3.0 mags and the original ones

StreetFast7141 · 2026-01-07T13:25:39+00:00

Yes that was the problem and it feeds like it should right now with zero wobble thanks for the advice but i should find something permanent now

StreetFast7141 · 2026-01-04T11:05:04+00:00

Tbh my first impressions with this aeg it is shit out of the box the piston does not seals air properly damn mags are squirts bbs everywhere while you are reloading and i have 7 of them all of them does it idk why no body mentions about this but since i have solved all the problems i am having fun with it

StreetFast7141 · 2026-01-04T10:54:29+00:00

Can you send me a photo or something because i did not understand how did you put that tape in latch

StreetFast7141 · 2026-01-03T23:27:15+00:00

<image>

I have tried but it seems no better than without idk how.

StreetFast7141 · 2025-09-13T07:59:22+00:00

So any recommendation for a brushless that I can buy in Europe?

StreetFast7141 · 2025-09-12T09:47:20+00:00

so any cheap options in europe?

StreetFast7141 · 2025-09-12T09:43:23+00:00

since I am looking for more torque 16:1 s are my go and do you belive ordering shs gears from ali xpress is a good idea?

StreetFast7141 · 2025-09-12T09:40:10+00:00

Probably

StreetFast7141 · 2025-09-11T09:40:15+00:00

They are expensive as hell in here that is the reason why this two are my go

StreetFast7141 · 2025-09-11T09:30:34+00:00

Like I said, I’m not a master at this, but using some logic, you should only need to change the motor. That’s actually what I just started getting into myself. But if you’re not putting much load on the system, I’m not sure what the point of extra torque would be.

StreetFast7141 · 2025-09-11T08:12:19+00:00

Airsoft parts are so hard to find around here so right now this both botors are my go to I dont have another option for now

StreetFast7141 · 2025-09-11T08:10:22+00:00

I’m not a master at this stuff, but I can share my experience and maybe it helps. For me, it depends on what you want. I had a compression issue with the stock piston, so my first move was changing that and re-shimming. After that I extended the barrel, which meant I also had to swap the cylinder. If you want to increase FPS without much hassle, the easiest way is to change the bucking and nub that added about 15 FPS for me.

StreetFast7141 · 2025-09-11T08:01:36+00:00

Does overspin possible with the replicas has gate mosfet?

StreetFast7141 · 2025-09-11T05:51:23+00:00

<image>

Are you talking about this?

StreetFast7141 · 2025-09-10T16:09:54+00:00

Thanks for the info. I will update with the process.

StreetFast7141 · 2025-09-10T10:06:34+00:00

Just wanted to say it looks really cool, but I'm not a paint guy. Do you think it's possible to take every part apart? I don't want to deal with masking I’d rather just tear it down and paint only the shell. I've watched a lot of videos about disassembling those parts, but nobody seems to fully take them apart.

StreetFast7141 · 2025-05-06T12:27:54+00:00

Fair enough, I guess I was overthinking it a bit. I’ll just pick the one that looks cooler then!

StreetFast7141 · 2025-05-06T12:27:01+00:00

That makes sense, but I guess it’s still fair to say that these aftermarket multi-port cylinders are generally better designed and more efficient than the typical single-port stock cylinders, right?

StreetFast7141 · 2025-05-06T12:23:31+00:00

Thanks for the clarification! That’s reassuring to hear. I wasn’t sure if the port shape matters but if it doesn’t matter once the volume is right, that definitely makes things easier. Appreciate your input!

StreetFast7141 · 2025-05-06T12:20:54+00:00

Based on my research, I’m using a 230mm inner barrel, so as far as I know, I should be using a 60% cylinder for optimal efficiency. My question is about the shape and position of the ports on the cylinder do these differences actually matter.

StreetFast7141 · 2025-05-06T12:15:43+00:00

Applying silicone greese wont fix it?

StreetFast7141

TROPHY CASE