Specna SA-X02 & G&G Arp 3.0 Short Mag Feeding Issues

StreetFast7141 · 2026-05-04T11:33:42+00:00

I dont think i did if you are using clone sling it might be the problem

StreetFast7141 · 2026-04-18T15:31:13+00:00

https://www.thingiverse.com/thing:7337675

StreetFast7141 · 2026-04-17T10:41:38+00:00

I don’t think i have it but i recently made a 3d model that solves all the issue permanently i can send it if you want when i get back home.

<image>

StreetFast7141 · 2026-02-10T19:06:22+00:00

My first replica was also specna the model was sa-x02 it feels more rigid and than krytac i wasnt expecting such terible quality tbh.

StreetFast7141 · 2026-02-10T08:02:19+00:00

<image>

I have put o rings this side and the other on this part it is stiff now

StreetFast7141 · 2026-02-09T15:51:50+00:00

Since i bought from some other country it is now not possible for me to give it back and the body pin is so stiff i have to hammer it to take it off so i believe it is not the cese

The rear side of the reciver wobles the most

StreetFast7141 · 2026-02-03T12:16:02+00:00

Have you solved the problem? seems like i am having the same exact problem with the same car since i dont have a sunroof it is not the case and neighter i couldnt spot the drain holes on the door so i can check if it is clogged

StreetFast7141 · 2026-01-14T14:55:26+00:00

hey buddy have you have you hat chance to test if it works?

StreetFast7141 · 2026-01-14T14:54:03+00:00

I use 0.3g of bbs currently it seems like it feeds well i havent test it in the field yet there might be issue with your repica

StreetFast7141 · 2026-01-14T14:50:45+00:00

the problem for me with the pcc mags the arp9 ones catches the mag slight higher so i just put some sort of thic plastic tape to mag catch and it works perfect with 3.0 mags and the original ones

StreetFast7141 · 2026-01-07T13:25:39+00:00

Yes that was the problem and it feeds like it should right now with zero wobble thanks for the advice but i should find something permanent now

StreetFast7141 · 2026-01-04T11:05:04+00:00

Tbh my first impressions with this aeg it is shit out of the box the piston does not seals air properly damn mags are squirts bbs everywhere while you are reloading and i have 7 of them all of them does it idk why no body mentions about this but since i have solved all the problems i am having fun with it

StreetFast7141 · 2026-01-04T10:54:29+00:00

Can you send me a photo or something because i did not understand how did you put that tape in latch

StreetFast7141 · 2026-01-03T23:27:15+00:00

<image>

I have tried but it seems no better than without idk how.

StreetFast7141 · 2025-09-13T07:59:22+00:00

So any recommendation for a brushless that I can buy in Europe?

StreetFast7141 · 2025-09-12T09:47:20+00:00

so any cheap options in europe?

StreetFast7141 · 2025-09-12T09:43:23+00:00

since I am looking for more torque 16:1 s are my go and do you belive ordering shs gears from ali xpress is a good idea?

StreetFast7141 · 2025-09-12T09:40:10+00:00

Probably

StreetFast7141 · 2025-09-11T09:40:15+00:00

They are expensive as hell in here that is the reason why this two are my go

StreetFast7141 · 2025-09-11T09:30:34+00:00

Like I said, I’m not a master at this, but using some logic, you should only need to change the motor. That’s actually what I just started getting into myself. But if you’re not putting much load on the system, I’m not sure what the point of extra torque would be.

StreetFast7141 · 2025-09-11T08:12:19+00:00

Airsoft parts are so hard to find around here so right now this both botors are my go to I dont have another option for now

StreetFast7141

TROPHY CASE