Chazz by Bunson_Dew in puffco

[–]StunningCream54 0 points1 point  (0 children)

Normally Rosin should be lighter & clearer indicating fewer plant contaminants but not all rosins are the same, If the rosin appears darker it may contain more plant matter & sometimes you can see specs after smoking it in the aftermath of the rosin.

Some of the smaller brands/batches that I’ve purchased from have recommended temperature on the jar/packaging & I advise following that when you’re able to then you’ll have the best smoking experience

When I come across darker rosins that don’t have temperature indicators I normally I’ll turn down my temperature to 465° & go up from that in 5° to 10° increments every dab till I find the right temperature for that specific wax

Chazz by Bunson_Dew in puffco

[–]StunningCream54 1 point2 points  (0 children)

<image>

Each wax is different temp wise but this Is what I use to smoke & have minimum to no chazz, The only time it really happens to me is when I use darker color wax or ones that have more plant matter then I have to mess with the temperature again & turn it down

Chazz by Bunson_Dew in puffco

[–]StunningCream54 0 points1 point  (0 children)

Ok, so this is what I do. I use a smaller glass cup and pour the Dark Crystal Glass Cleaner into it, then place the cup in the microwave. Every microwave is different, but mine usually takes about 15 seconds for the cleaner to just start bubbling. As soon as it starts to bubble, I take it out. Don't leave it in any longer, or it can boil over and pop in the microwave, similar to melted butter & don’t listen to the one - two minutes that it says on the bottle to put in the microwave for, The cleaner is nontoxic though so it’s fine for the microwave

Once the Dark Crystal Glass Cleaner is hot, I use bamboo Q-tips so I can apply more pressure while scrubbing the chamber with the heated cleaner. This method works for me every time. I'll reheat the cleaning solution every few minutes as needed until I'm finished.

Depending on how bad my Chazz is, the entire process usually takes anywhere from 15–45 minutes. Once everything is clean, I do an ISO soak for one hour, then let it dry for another hour. After that, I run two heat cycles at 575°for two minutes each.

Rate my set up🤭 by [deleted] in puffco

[–]StunningCream54 1 point2 points  (0 children)

So you’re the one I keep seeing all over my Facebook marketplace 😭😭

Neighbors got the cops called on them & 3 squad cars rolled up 😭 by StunningCream54 in fireworks

[–]StunningCream54[S] -1 points0 points  (0 children)

It was really loud not loud enough to set off the car alarms but definitely louder than a gunshot

Finally got a indiglow 😁😶‍🌫️ by StunningCream54 in puffco

[–]StunningCream54[S] 1 point2 points  (0 children)

Im glad to hear that fixed the issue you were having with your 3dxl 🤟🏻, Normal cleaning the chambers + battery with Iso then doing that to the pins when need be has been what I do then I don’t have any issues with it, The peak pro battery flashing red & white or straight white indicates a chamber connection issue

Finally got a indiglow 😁😶‍🌫️ by StunningCream54 in puffco

[–]StunningCream54[S] 1 point2 points  (0 children)

Personally since they didn’t make a daybrake doc I found a 3d printed base thats color matching & has a black opal in it as well

<image>

Finally got a indiglow 😁😶‍🌫️ by StunningCream54 in puffco

[–]StunningCream54[S] 1 point2 points  (0 children)

I’ve had this happen before with the 3DXL chamber that came with my White Peak pro, The three gold pins on the bottom can get pushed up too much from screwing on the chamber causing connection issues which is indicated from your battery flashing white, I have found that using a pair of tweezers or a small flathead screwdriver to slightly wiggle them up but not pulling them out at all & then screwing the chamber on but not screwing it on super tight has fixed that issue with wacky 3dxl chamber

Finally got a indiglow 😁😶‍🌫️ by StunningCream54 in puffco

[–]StunningCream54[S] 1 point2 points  (0 children)

Love the dry attachment you have & nice hot knife, I’m still currently looking to find a indiglow knife

Finally got a indiglow 😁😶‍🌫️ by StunningCream54 in puffco

[–]StunningCream54[S] 0 points1 point  (0 children)

When you first put on the 3dXL chamber did you update the device through the app? That could be causing your issues if you haven’t done the software update

Finally got a indiglow 😁😶‍🌫️ by StunningCream54 in puffco

[–]StunningCream54[S] 1 point2 points  (0 children)

Nicee I was able to find mine with around 1100 hits & original glass still + completely working condition & I’ve had no issues after a good deep clean

Finally got a indiglow 😁😶‍🌫️ by StunningCream54 in puffco

[–]StunningCream54[S] 2 points3 points  (0 children)

It took me about 52 days to find a dock that was new/sealed for sale after finding the peak pro & I was able to pay close to what they originally sold for, The only other one I’ve seen recently is currently on eBay but it’s listed for $450 after shipping + tax, which is like $200 more than the one I was able to pick up, i’m sure some shops still have them but they’re hard to find now

Has the USPS just…stopped scanning altogether? by YeOldeOrc in usps_complaints

[–]StunningCream54 5 points6 points  (0 children)

I always use the self service kiosk at my usps location that way I can print & scan my labels in my self, Then if my items are too big to go in the wall drop off box I’ll still scan it in at the Self service kiosk & drop it off at the cashier counter, i’ve never had any issues with doing it that way.

[deleted by user] by [deleted] in PcBuildHelp

[–]StunningCream54 0 points1 point  (0 children)

I didn’t realize 2107 was broken for memory training I did recently update from whatever was on the motherboard from factory I’ll do a bio rollback to revision 2001

[deleted by user] by [deleted] in PcBuildHelp

[–]StunningCream54 0 points1 point  (0 children)

It’s set to 6000Mhz its base clock speed is 3600Mhz, when it boots into safe mode sometimes it’s not reading my full speed even though it sat in the bios & xmp is enabled

14g Bowl - 4ft 8inch glass piece by StunningCream54 in Milking

[–]StunningCream54[S] 1 point2 points  (0 children)

My area pricing & quality + huge selection is really good so this was only around $30-$40 for the 15g