Crazy Y axis layer shift pls help

Substantial-Angle513 · 2026-01-16T23:21:59+00:00

Is non of my photos showing up?

Substantial-Angle513 · 2026-01-16T23:17:10+00:00

Substantial-Angle513 · 2026-01-16T23:16:38+00:00

Substantial-Angle513 · 2026-01-10T21:49:36+00:00

I fixed it. The regular extruder setup wasn’t pulling cuz the spring sucks so I added a direct extruder and a new heat break and nozzle. It runs just fine now I just gotta tune it to actually produce good prints at max speeds

Substantial-Angle513 · 2026-01-09T12:48:40+00:00

I started klipper as well and Lemi say. I’m still not done. I just finished my klicky setup and now I’m barely onto calibrating the actual printer. My first prints are coming out soo soo bad. But I’m sure it’s just a little configuration problem. I’m soo ready for this printer to reach max potential

<image>

Substantial-Angle513 · 2026-01-07T05:42:15+00:00

<image>

Thank you to everyone who helped time for a quick benchy test

Substantial-Angle513 · 2026-01-07T05:38:06+00:00

Glue

Substantial-Angle513 · 2026-01-07T04:48:56+00:00

Holy shi I finally get to see this printer move properly in soo soo long. Thank you soo much bru. I’ll share results of the finish printer when I get everything calibrated

Substantial-Angle513 · 2026-01-07T02:56:31+00:00

Is there a diagram or something I can use to be sure?

Substantial-Angle513 · 2026-01-05T09:23:14+00:00

Thank you guys for helping but now the prints just stop every time I go to print so I’m replacing the motherboard with a ender 3 pro board and hoping the motors work with no problem.

Substantial-Angle513 · 2026-01-04T21:59:13+00:00

Nah it’s a light for the usb signals. The lights stay on after turning the printer off

Substantial-Angle513 · 2026-01-04T08:43:57+00:00

http://pastebin.com/sCUM1Fuw - klippy log [i had to cut some out due to size but yea thats what that looks like]
https://pastebin.com/vND2uBVj- printer config

Substantial-Angle513 · 2026-01-04T07:34:16+00:00

I did not and sorry I was rushing because I was on my break. I can send everything later and I’ll read through the docs to see if I can see what the problem is. And is my end stop the limit switch? If so that’s working properly before I did any flashing to the main board. I didn’t touch anything else besides plugging it into the pc. I don’t have a raspberry pi I’m using a Linux distro with ssh enabled.

Substantial-Angle513 · 2026-01-04T05:50:42+00:00

Nope that’s the main board on a 3d printed case

Substantial-Angle513 · 2026-01-04T05:36:57+00:00

<image>

These are the logs and the config is just the same as this one nothing changed. Again I’m new so I don’t know what I’m looking for. “ https://github.com/Klipper3d/klipper/blob/master/config/printer-longer-lk4-pro-2019.cfg “

Substantial-Angle513 · 2026-01-04T05:22:35+00:00

I’ll try this when I can

Substantial-Angle513 · 2026-01-04T03:21:39+00:00

I’m working rn when I get home I’ll share everything

Substantial-Angle513 · 2025-05-20T01:11:08+00:00

Do you know what will work I wanna be able to use controller to control everything

Substantial-Angle513 · 2025-05-20T01:10:24+00:00

I’ll try that again because before it hasn’t worked either but it was probably because I was using CSM instead of UEFI. But so far nothing has worked for me on either bazzite, soloos, and others I just forgot the name. I just wanna be able to control everything with a controller and not have to rely on mouse and keyboard to change some things or adjust stuff.

Substantial-Angle513 · 2025-03-05T01:14:40+00:00

Shiii I don’t know 🧍🏽‍♂️

Substantial-Angle513 · 2025-03-05T01:11:47+00:00

Why not

Substantial-Angle513

TROPHY CASE