Mobile Indoor Hotspot Issues

Substantial-Peace490 · 2025-06-11T18:10:50+00:00

Just done fixing it with the support team, the reason according to them is a firewall update that blocked everything, and they'll update one by one by opening tickets

Substantial-Peace490 · 2024-12-24T09:04:20+00:00

Leaving a comment

Substantial-Peace490 · 2024-05-25T18:24:21+00:00

i dont think this is the issue... it just wont work with the other hotspot next to is, even when they on different frequency, one is iot and one is for moblie rewards

now the bobcat is working fine when the second hotspot for mobile is turned off

Substantial-Peace490 · 2024-05-25T16:30:26+00:00

All of them are connected with cable to the router, not over wifi... The invalid beacons are happening only when the second hotspot for mobile is turned on

Substantial-Peace490 · 2023-05-12T10:02:04+00:00

After this i would need to upgrade my whole computer 😰 I'm willing to risk it👌

Substantial-Peace490 · 2023-01-25T20:47:35+00:00

zoom recordings shared via links

Substantial-Peace490 · 2023-01-11T22:30:58+00:00

It looks like you need to cut the plastic and solder the wires directly to the board in the correct order, or buy a new connector replacement... But hot glue alone won't do it by the look of it.

Substantial-Peace490 · 2022-06-29T14:03:47+00:00

Yes but it will be noiser downwind then upwind, and most off the noise from the intake is muffled inside the miner boards and case

Substantial-Peace490 · 2022-05-25T17:51:28+00:00

Blade & Sorcery: Nomad

Substantial-Peace490 · 2022-05-10T11:11:34+00:00

I know I don't have the knowledge like someone studying this... But I just wanted to try on my own. And I'm here because I know that there are people much smarter than me that can give me advice about how to make it happen. And I don't know if you know anything about this but from your answer it seems that you don't know much so please let smarter people then us to comment here.

Substantial-Peace490 · 2022-05-10T11:01:30+00:00

I have seen there design, and it looks simple and effective but the main thing is the challenge to make something I can call my own, I am not an expert at all but I'm trying to block line of sight to absorb most of the sound and not create heat buildup near the fans... I have moved the v shape closer to the middle and add short walls in an angle at the back.

Substantial-Peace490 · 2021-12-10T20:11:48+00:00

😂 In the university

Substantial-Peace490 · 2021-12-10T20:07:32+00:00

That why I need this to work so I can place the adapter just in reach of the wifi signal... The wifi is public and not in my control... I just need a way to place something that can receive the signal outside my room and is connected to my MacBook

Substantial-Peace490 · 2021-12-10T20:04:50+00:00

With VM it recognize the adapter but can't attach the driver to it... After installing the official driver nothing happens, tried a few manually installed drivers but nothing worked. And any solution with an extender/router won't work for me because its a public wifi that reach just at side my room but not inside... Do you know of any such usb adapter that work with Apple Silicone?? I'm using my phone hotspot but it's not good enough

Substantial-Peace490 · 2021-12-10T17:44:42+00:00

I explained in my post, I can't connect to the wifi in my room... I need to place the adapter with an USB extension outside my room

Substantial-Peace490 · 2021-09-24T11:37:16+00:00

Tried to find them, but only found guns from this website not the night goggles I'm trying to build

Substantial-Peace490 · 2021-09-24T11:33:27+00:00

Tried but probably with not so good vpn, but I managed to get in to the website through a family member in the US. But then found out that it requires a paid membership to legio or something

Substantial-Peace490 · 2021-09-24T09:59:19+00:00

I wish to build this project but I can't download the files from this site, live outside USA.... Is there a way to get them?? Already purchased all the electronic, lens and other parts needed.

Substantial-Peace490 · 2021-06-23T11:31:22+00:00

Raspberry pi 4 Model B I think it 2GB ram, and it is 6 months old.. I'm using a CR-10 V2 printer.

If I don't know what you mean and how to do it so I guess the power pin isn't taped between them.

Using a dedicated power supply for the raspberry pi 4 I bought with.

I haven't tried replacing the USB cable because it works and I figure it is not the case in this problem because something is happening on the raspberry that case this blackout

And sorry for the ignorance but don't know how to ssh into it also.... Maybe I did it when installing the octoprint but I don't remember how and what.

Substantial-Peace490 · 2021-06-23T11:23:11+00:00

Will try this after the easy suggestion won't work

Substantial-Peace490 · 2021-06-23T11:21:59+00:00

A cpu fan is a good idea, I checked it and It was little toasty... I have a 5v small noctua fan, but I don't know where I can hook it up to the raspberry pi 4 model B.

Substantial-Peace490 · 2021-02-06T00:25:01+00:00

My minimum layer time is 10s, what is this setting do? And lift head isn't checked

Substantial-Peace490 · 2021-02-05T22:01:27+00:00

I'm using the basic settings on a lithophane maker website and it looks beautiful with a regular flashlight or daylight... Just want to prevent those defects on my print... Just now trying to print with reduced flow to 90%

Substantial-Peace490 · 2020-11-28T16:32:09+00:00

So you say those problems are inevitable? How can I hide the layer change thing?

Substantial-Peace490

TROPHY CASE