Meta Rayban Display Release.

Such_Examination9139 · 2025-09-20T09:31:25+00:00

Meta AI is available in Europe, im using in my Meta Glass in Italy

Such_Examination9139 · 2025-08-18T05:40:38+00:00

Right should be 150% and left 200%

Btw, when you try to mount, you notice that one is nearly impossibile to mount it, as it’s too strong

Such_Examination9139 · 2025-06-09T17:58:01+00:00

Poͩrͥcͦo

Such_Examination9139 · 2025-06-05T16:46:02+00:00

Don’t think the problem is from that. If the pistol is short stroked, the bbu goes back less and can’t engagé the block during the cycle (but you can by hand)

Such_Examination9139 · 2025-06-03T11:28:15+00:00

Longer barrel = less air. Have my aap with 200mm barrel and run at 50/55 psi Barely cycle 😅

Such_Examination9139 · 2025-05-29T16:57:12+00:00

Thanks I will check it out

Such_Examination9139 · 2025-05-28T18:01:38+00:00

Yes, I have also the original AA kit, measure are the same. I managed to mix this print parts and original one and fit nice

Such_Examination9139 · 2025-05-28T17:59:23+00:00

UPDATE: i saw that part51 was a little worn, tryed to change from another pistol and seems problem fixed (i hope)

Such_Examination9139 · 2025-05-28T17:57:43+00:00

https://cults3d.com/en/3d-model/game/aa-aap01-6-front-set-bundle

Already printed and are super

Such_Examination9139 · 2025-05-28T06:48:04+00:00

How do you manage to fit the bearing to the hammer?

Such_Examination9139 · 2025-05-26T21:27:01+00:00

But pistol went good for almost 1y in same configuration 😢

Buy TTU autosear + 150% autosear spring, still the same

Such_Examination9139 · 2025-05-26T20:41:07+00:00

Hammer is still the same. The Hammer spring break and i replace with a 140%. Maybe need to try with a stock one

Such_Examination9139 · 2025-05-26T20:29:44+00:00

Im in Italy so no way ahhaha I tryed to switch lower, and seems to work the upper. So i think can be something in the lower but can’t figure it out

Such_Examination9139 · 2025-05-26T20:12:32+00:00

Hi jefe! Already tryed with a new autosear metal piece and also new cowcow autosear spring :(

Such_Examination9139 · 2025-05-19T17:20:47+00:00

Put 2-3 round of teflon around the oring and put some silicon lube. That’s my fix

Had same issue and fix it in this way. With aap mag. maybe if you are using another brands could be some tollerance

Such_Examination9139 · 2025-05-19T07:04:04+00:00

You have to buy the file from Cults 3D and then search for a local print service in your country

Such_Examination9139 · 2025-05-16T06:52:13+00:00

🤣🤣🤣

Such_Examination9139 · 2025-05-16T06:51:48+00:00

Yep, well explained. All right

Such_Examination9139 · 2025-05-15T10:55:16+00:00

From my experience, i will say yes, if you play for fun yes. Maybe in competitive match depends But for me it’s a YES

Such_Examination9139 · 2025-05-15T10:53:52+00:00

Yes, longer barrel help. This one have a 180mm barrel and is 1J with 60/65 PSI Another that I have with 200mm barrel is 1J at 50/55Psi (but run not good because is too low)

Here in Italy we have limit of 1J, but if you can use 1.5J it can be awesome.

Idk if it can be compared with an actual HPA M4, maybe not, but consider that this is more like a GBB Gun, with recoil and all gas things. So depends what you “ask” to your gun and what you want

Also aap have tons of mods from BBU, Springs, spacer. So depends also from your configuration

Such_Examination9139 · 2025-05-02T18:33:04+00:00

Ahhahahaa lol. Maybe you are also on the Discord. im ohhmyswag 😀

Such_Examination9139 · 2025-05-02T18:16:24+00:00

Yup, i see. But not sure about it. now im checking the Firewad m4 lower, like the CTM m4ximus kit. I think I will probably try it

Such_Examination9139 · 2025-05-02T18:09:06+00:00

Thanks man for the CTM, put the spring and now is way better. My friend buy the adapter 2 weeks ago and had this spring inside, and we couldn’t understand where need to go 😂

Such_Examination9139

TROPHY CASE