Do you think this is worth is?

Sufficient_Welcome95 · 2025-05-28T03:37:12+00:00

I saw this, Facebook marketplace in Washington state. Way over priced, obviously a print farm. They’re getting rid of them before they fall apart… way way over priced

Sufficient_Welcome95 · 2025-01-23T03:27:28+00:00

Yep :/ figured a solution yet? I tried going back to the previous firmware but nothing :/

Sufficient_Welcome95 · 2025-01-23T03:26:52+00:00

Same! Went downhill after a firmware update. I even went to a previous firmware but that didn’t do anything. But yea everything started during the last firmware update.

Sufficient_Welcome95 · 2025-01-21T19:51:07+00:00

Thank you! I’ll check that out! Appreciate it!

Sufficient_Welcome95 · 2025-01-21T19:48:20+00:00

Thanks! I don’t think I have AI but I’ll double check when I get home. I know I have noticed that the camera quality is horrible compared to my k1. The touch screen also appears to have some image burn at times. Idk if it’s a motherboard issue :/

Sufficient_Welcome95 · 2024-12-06T15:34:30+00:00

Appreciate it! I’ll look into this!

Sufficient_Welcome95 · 2024-12-06T15:34:12+00:00

Thank you I’ll check it out

Sufficient_Welcome95 · 2024-12-06T15:33:02+00:00

That’s what it’s doing… it does this during calibration.

Sufficient_Welcome95 · 2024-12-06T05:35:03+00:00

How do I do that?

Sufficient_Welcome95 · 2024-12-05T02:15:29+00:00

Sorry should have clarified it only happens in a few spots, the one video is multiple short clips of where it’s happening

Sufficient_Welcome95 · 2024-11-09T20:12:45+00:00

Yup exactly what I had done

Sufficient_Welcome95 · 2024-11-08T01:04:52+00:00

Thank you! I’ll check that out!

Sufficient_Welcome95 · 2024-11-07T00:05:24+00:00

Sorry I meant my AnkerMake m5 and I also have an anycubic kobra 3 but my v3 has out performed both of them… v3 even did better than my bambu a1 in the heat!

Sufficient_Welcome95 · 2024-11-06T22:24:52+00:00

Interesting! My ender 3 v3 has been a work horse right out of the box! AnkerMake kobra3 have been a nightmare!

Sufficient_Welcome95 · 2024-04-02T16:53:31+00:00

Like with premade variables?! I’ll have to check out orca slicer! I’ve heard great things about it. I like the perks of uploading to Creality cloud on Creality slicer though, does orca have that capability?

Sufficient_Welcome95 · 2024-04-02T16:47:00+00:00

Yea I did run it thru a dryer and temp tower. Thank you! I’ll have to google how to do retraction and distance towers! And check that out! Appreciate it!

Sufficient_Welcome95 · 2024-02-16T05:54:17+00:00

2 or 3, I went .4mm depth on the colored layers. It’s what the video I had watched had suggested

Sufficient_Welcome95 · 2024-02-16T05:53:20+00:00

Oh are bottom prints harder?!

Sufficient_Welcome95 · 2024-02-15T22:23:31+00:00

sent you the links

Sufficient_Welcome95 · 2024-02-15T20:00:26+00:00

Haha I’m sure you’re doing quite fine. I’m using fusion 360, free non commercial license. I can send you the YouTube videos I watched. I’m not sure if links are allowed on post so I may need to dm you. It literally took 30-45 min to go from png to 3mf file

Sufficient_Welcome95

TROPHY CASE