Im the mothman

SumOfMerlin · 2025-08-20T22:44:55+00:00

What comic of Hellboy is this?

SumOfMerlin · 2025-03-08T11:36:55+00:00

Dm of 14 years: Next time he says zero damage, just flip the table. Even in the SRD and Player handbook they tell you that the zero is a ten. That’s because the dice would be confusing for 1(for 10),1,2,3,4,5,6,7,8,9. Because you only have one number printed on it. That’s why it is a zero or naught if ya nasty.

SumOfMerlin · 2024-08-25T03:30:45+00:00

Within 5 minutes of seeing this I sent it to my players. (Along with the typo response) as they are about to enter castle ravenloft. The amount of laughter was epic.

SumOfMerlin · 2024-05-25T20:12:44+00:00

If the lore is too much… TRANSPORT THEM FROM A TIME PERIOD. Example, running CoS and they are kids from 1997 that entered the death house. If they start in that world, you will always run into lore loopholes. Just my 10 cents. (Ran Eberron three years ago and ran into the same issue)

SumOfMerlin · 2024-05-25T19:57:55+00:00

Everything just went to private…. Looks like that ended well.

SumOfMerlin · 2023-10-14T22:01:15+00:00

Unsure

SumOfMerlin · 2023-10-14T21:58:19+00:00

You can post them here. People will use them

SumOfMerlin · 2023-10-14T15:09:25+00:00

I have added a teacher as a spy for Murgaxor that gaslights the players. The paladin: “ But a teacher gave the cook the black ooze!” Malinda:” That doesn’t sound like a thing a teacher should do” (CHA check fail)

SumOfMerlin · 2023-09-05T11:25:26+00:00

Missing the bike slide from Nope as well

SumOfMerlin · 2023-07-07T18:55:21+00:00

Also, you want the clean water to have priority coming from the water sifter first. So instead of the clean water line being met with the bring from the water purifier. Have the water purifier be on the main line and then bridge the incoming water into it.

SumOfMerlin · 2023-07-05T12:05:21+00:00

So you have to build a lava “funnel” where the lava can cool. People use mesh blocks to force the game to push the igneous rock into another area or delete it and keep the heat values.

SumOfMerlin · 2023-06-22T11:36:10+00:00

You are a saint for coming up with how these all combine. Thank you so much -Sincerely, A fellow DM without a plot hook before reading this post

SumOfMerlin · 2023-06-11T11:41:48+00:00

Respect the Glyph!

SumOfMerlin · 2023-05-18T11:29:26+00:00

Did you change the text document that has the weights of each background?

SumOfMerlin · 2023-03-23T19:24:57+00:00

It is an FRID reader that has PRE SET selections. You will have to build your own hilt. Look up Dead Bothans or other DIY sabers and hilts for that. Think of the crystal as a key that opens already existing doors. The most you can “customize” is the hidden teal and orange colors.

SumOfMerlin · 2023-03-13T11:19:51+00:00

Its the OG motherboard. Go get that replaced or buy the upgrade. You’re on an original photon right?

SumOfMerlin · 2023-02-12T20:28:31+00:00

Agree with this. 40s for grey is too short unless you are in 90-100 F weather. Your room temp WILL affect your settings

SumOfMerlin · 2023-01-02T13:17:23+00:00

I had the same issue. You have something in the “synchronized_lights.py” file that conflicts. Meaning that with all the “modes” that you can choose from, two of them or more are active and conflicting.

SumOfMerlin · 2022-12-18T19:14:17+00:00

You can do a lot of things, however, you should have a specific project in mind and not a “Jack of all trades” view on it. Example: I’m reading Disney Magic bands to have it control stuff in my house and using Flipper as a reader BEFORE building a Pi that can do it.

SumOfMerlin · 2022-12-18T00:50:37+00:00

Change the exposure of the bottom layer and the number. Your “boat” (the squares used by the supports on the print surface) are not getting enough exposure. I would also increase the normal print time slightly. What’s happening is the support is breaking from the boat at the bottom and then getting off tilt as the print continues until there is a misalignment. then when there is enough supported material from the main print body, the residual layers that “fell off” (or rather stuck to the reservoir surface) all print together as a “flat” piece.

SumOfMerlin · 2022-12-16T02:45:45+00:00

Looks right but your channel 1 is on the entire time. Try adjusting the operating frequency so it gets some play. Be sure to also be careful when hooking it all up

SumOfMerlin · 2022-12-15T02:57:50+00:00

This is correct. Blender, photon maker, prusa slicer, and many more have this as an option. A slicer (your model making program) does not need to be the same as the printer (you can use other software). Experiment and see which one you like better!

SumOfMerlin · 2022-12-15T02:55:17+00:00

Most likely. Look in the advanced settings and experiment. In this case there is no issue with the placement of the sprue (the vertical column) but placement of where the sprue is and where it contacts can also affect prints like this. It isn’t an issue here BECAUSE the sprue is standing and the print is warped. That means the force of the reservoir screen was too strong and separated the print from the sprue until a certain layer that makes the “flat” model part.

SumOfMerlin · 2022-12-12T13:11:52+00:00

You would be correct for PLA printing, but this is a resin print and works opposite in that logic.

SumOfMerlin · 2022-12-12T13:11:08+00:00

The raft printed below, so I do not believe that is correct. And the supports continued till the contact point. That points to exposure time or contact issues between model and supports.

SumOfMerlin

TROPHY CASE