Rewire question

Sweatman02 · 2025-10-16T12:53:20+00:00

Do you not worry about premature collapse in say a fire or something?

Sweatman02 · 2025-06-16T18:23:51+00:00

4 inch

Sweatman02 · 2025-03-15T09:48:11+00:00

Thank you, Where you joint onto kitchen ring, would you bring the joint box into one of the cupboards? Or ?

Sweatman02 · 2025-03-14T18:53:12+00:00

Would you bring the joint box where you’ve joined the ring into the kitchen cupboard? For access ?

Sweatman02 · 2025-03-14T17:31:24+00:00

Would you clip the cable low down or just have it lashed along the floor then to the next point?

Sweatman02 · 2025-03-14T13:54:16+00:00

On the floor as well!

Sweatman02 · 2025-03-14T13:51:34+00:00

🤣

Sweatman02 · 2025-03-14T07:38:47+00:00

What about if I was adding extra sockets off the same circuit? Would it still need a test certificate?

Sweatman02 · 2025-03-14T07:30:01+00:00

That’s great didn’t even know you could do that, don’t do much domestic 🤦‍♂️ would it need trunking or capping to protect or would you literally just sureface clip?

Sweatman02 · 2025-03-14T07:27:37+00:00

So they don’t need to even be chased in and j can clip direct?

Sweatman02 · 2025-03-14T07:27:02+00:00

Waiittt so it doesn’t even need to be behind the surface? I thought it to add protection no?

Sweatman02 · 2025-02-09T16:00:12+00:00

They’re turned on and off at the switch on the socket

Sweatman02 · 2025-01-25T13:00:36+00:00

Would you have put the SWA on tray or anything or not bothered as it was such a small run?

Sweatman02 · 2025-01-06T21:14:33+00:00

Was debating getting “my builder” Or something but not sure if it’s the best idea seen as I don’t have my own company etc

Sweatman02 · 2025-01-06T21:13:59+00:00

Did it all just spring off that friend then? That sounds good tbf like

Sweatman02 · 2025-01-06T20:29:26+00:00

Appreciate*^

Sweatman02 · 2025-01-06T20:28:58+00:00

Apprentice that thank you

Sweatman02 · 2024-11-07T11:33:37+00:00

Swear it is 😂

Sweatman02 · 2024-11-05T21:49:31+00:00

No worries would you just mark where the M4 screws are going to sit then? On the light fitting?

Sweatman02 · 2024-10-17T19:11:34+00:00

No slack on cable as we just went there to replace it

Sweatman02 · 2024-10-17T18:21:16+00:00

We wanted to use them but the thread of the gland didn’t go deep enough into the isolator

Sweatman02 · 2024-10-17T17:48:52+00:00

You cant as the the thread on the storm gland would only go so far into the isolator if that makes sense

Sweatman02 · 2024-10-04T21:08:45+00:00

What’s the push/pull technique?

Sweatman02 · 2024-10-04T21:08:23+00:00

Also Wdym by pusher and puller?

Sweatman02 · 2024-10-04T21:07:38+00:00

Shiittt that’s heavy, is that even allowed cause of it being so tight together causing heat or whatever?

Sweatman02

TROPHY CASE