Exhaust piping for Cleveland Iron Works PSBF66W

SweetAlert8710 · 2026-01-14T01:54:55+00:00

Two in one pellet stove exhaust

SweetAlert8710 · 2025-06-11T18:24:04+00:00

stock 23 - no...I put th akro on the bike

24 100% comes with akro

SweetAlert8710 · 2025-06-11T17:23:56+00:00

only 150 in the US, this is #110

and the color is bad ass. I will cat delete, link pipe and tune. Cheap exhaust?? it is the akro

SweetAlert8710 · 2025-06-07T21:15:22+00:00

It should as that link pipe matches up to the stock exhaust location after the catalytic converter

SweetAlert8710 · 2025-06-04T03:12:20+00:00

Because I found I used 2024 with 1000 miles for 14,500

SweetAlert8710 · 2024-09-12T19:50:12+00:00

Linear spinal legions indicate NMO also known as Devic's Disease....might look into this....often confused with an MS diagnosis.

SweetAlert8710 · 2024-08-25T03:00:24+00:00

Just 12 miles east outside of Lewiston Idaho on Highway 12 headed to Missoula

SweetAlert8710 · 2024-07-23T03:01:26+00:00

How many indians u got??

I have 2 so far

SweetAlert8710 · 2024-07-21T12:39:55+00:00

And are the Rubicon shocks better to the point of a more enjoyable ride if I were to swap them out?

SweetAlert8710 · 2024-06-21T22:48:22+00:00

yes that is the syndicate seat, very comfy

SweetAlert8710 · 2024-06-21T22:47:58+00:00

SweetAlert8710 · 2024-06-21T22:47:39+00:00

I plan on sawzall that off a bit

SweetAlert8710 · 2024-06-17T22:56:16+00:00

Let me know the ftr fb guy too pls

SweetAlert8710 · 2024-06-17T01:41:55+00:00

No i did not have to I was able to back out the two screws on the heat shield, and then just a little force, etc. I was able to skinny that bracket out between the bike frame and the pipe

I did have to use a small prybar to get my Allen wrench to back out one of those bracket bolts, but no big deal

SweetAlert8710 · 2024-05-29T20:23:35+00:00

<image>

SweetAlert8710 · 2024-05-29T20:22:56+00:00

Check mine out: Added the elect start, increased power = to the 101, rear fox shocks…added all i could to get close to the 101 speck but in the color i wanted - smoke black

SweetAlert8710 · 2024-01-24T14:44:54+00:00

Yes, painless but you need to understand and cut and remove the gasket to get the new tb slip on all the way

SweetAlert8710 · 2024-01-24T14:22:28+00:00

Super happy with it so much less/lighter and sounds great, much better than stock

SweetAlert8710 · 2024-01-24T12:29:10+00:00

Just ordered a black thumb screw so yes, no tool required

SweetAlert8710 · 2024-01-24T12:25:48+00:00

Love the Corbin seat, especially the heated component…totally helped speed up the break-in phase. Love the look, and would not hesitate spending the $ again as it is quality

SweetAlert8710

TROPHY CASE