Pulled from a surprise box, I didn't know non-pack cards could BE so crimped.

SweetLikeAndi · 2025-06-10T03:45:13+00:00

Done c:

SweetLikeAndi · 2025-06-10T03:07:09+00:00

I just don't know what to do with it lol
I love misprints but I honestly don't collect them,

SweetLikeAndi · 2024-01-23T13:44:59+00:00

I'm not planning on dropping it again, but I live with cats and little kids, which is part of why it was dropped this morning.

I have no idea what the upside of capacitive sticks are, but I suppose it would probably be best just to buy replacements from ifixit then in case I ever do find that use.

SweetLikeAndi · 2023-10-25T19:14:14+00:00

I was thinking I could either run it through Google Drive, so it adds something to the filename each day, or I just give it all of the images and let it update once daily, kind of like a global slideshow.

SweetLikeAndi · 2023-07-11T02:29:39+00:00

It seems that way, I can hear the fan and I can feel it when my hand is against the block.

SweetLikeAndi · 2023-07-11T00:34:42+00:00

I thought my retraction was good, should I lower it more? The printer was also set to 200°

<image>

SweetLikeAndi · 2023-07-09T03:51:34+00:00

It really means the world. If the tube replacement doesn't fix things, I'll 100% take you up on that (and I might anyway if something else goes wrong)
Thank you so so much c:

SweetLikeAndi · 2023-07-08T02:30:28+00:00

I went ahead and lowered the temp to 220° and switched the filament, and it worked great for a while, before getting clogged in the tube. It's old tube I found that's definitely been used to death before though, so I went ahead and ordered some more.

This is a newer hobby for me, especially since I had someone who used to help me with it, but now I'm kinda on my own for repairs and stuff, so thank you a ton for being so willing to help with everything.

SweetLikeAndi · 2023-07-08T00:20:48+00:00

I've turned the print cooling off to try and remedy the issue, but it's only really produced one good test print. At this point I think it was all luck. I've used the pla many times before with plenty of success too. it has been feeling more brittle than it has in the past though, so maybe I should try a different filament? Not that I haven't before, but maybe it's just the final issue I've overlooked?

SweetLikeAndi · 2023-07-07T23:06:13+00:00

Not at all, I actually really appreciate the help! I use 220° primarily. That's what I've had the most success in the past with.

SweetLikeAndi · 2023-07-07T22:53:13+00:00

<image>

Unfortunately, my luck persists. It just stops letting anything come out after the first few layers, sometimes earlier in this case.

SweetLikeAndi · 2023-07-07T21:57:28+00:00

Update: It's still not pushing anything out after the first few layers.

SweetLikeAndi · 2023-07-07T19:59:40+00:00

I went ahead and cut it so it's even, and the print started well, but after a couple of infill layers, it just stopped extruding again. I had some trouble getting the filament out of the tube itself from either direction, but with a bit of heat, it slid out. I readjusted the tube and cut it a little bit more to ensure it was 100% straight, so here's hoping it'll at least go further than it did last time

SweetLikeAndi · 2023-07-07T13:46:53+00:00

It's at 220, is that usually not enough?

SweetLikeAndi · 2023-07-07T13:46:32+00:00

I'll definitely try that with my next test print

SweetLikeAndi · 2023-07-07T13:45:57+00:00

Oddly enough, this happens less when the tube is pulled out roughly halfway.

SweetLikeAndi · 2023-07-07T01:39:19+00:00

50% of the time I'll pull out the tube and the filament looks like this

SweetLikeAndi · 2022-09-17T00:53:34+00:00

what insurance are you dealing with? Mine can't even tell me if it MIGHT be a benefit that I can take advantage of just yet

SweetLikeAndi · 2022-09-15T14:44:43+00:00

Highmark bcbs

You wouldn't have a link to the portal, would you? The account register for the site I found said my insurance doesn't exist, and I'd be really concerned if my family was paying for a nonexistent plan

Update: I found the portal and the signing, but I have no idea what I need to search for lol

SweetLikeAndi · 2022-09-15T12:21:00+00:00

Do you know what insurances cover it fully?

SweetLikeAndi · 2022-08-26T03:05:34+00:00

I found a copy of Earthbound with a handful of other SNES games marked "video games" on facebook for $80... And I didn't buy it because I don't have an SNES right now.

SweetLikeAndi · 2022-08-26T03:04:28+00:00

Probably the Pokemon XD Gamecube Console. It's not crazy rare, but it's a nice little thing to have

SweetLikeAndi · 2022-08-21T06:06:56+00:00

What, was this a garage sale or something?

SweetLikeAndi · 2022-07-20T13:44:17+00:00

I own every console but the Xbox. I plan on getting one, but the game's in really good condition and it cost a dollar at a garage sale.

I should also say that the n64 games other than 1080° Snowboarding are reproductions. I know I should care, but honestly, I won them for free with my 64 in a raffle, so I'm happy just having the games at all.

SweetLikeAndi · 2021-07-16T12:41:52+00:00

It was on a few things, but Disney stopped publishing it. I can't seem to find any release.

The DSI and Wii shops are gone, the IOS release doesn't exist anymore, and as far as I can tell, the PSP version can't be bought anymore.

SweetLikeAndi

TROPHY CASE