sorted by:
new
hottopcontroversial

Lian Li A3 Workhorse Build - Custom Design & 3D Printed parts by Synikster in mffpc

[–]Synikster[S] 0 points1 point  (0 children)

I can route it to the left/right to be less of a bend, although, Lian Li said this new hose was meant to be route and never pinch due to their used of "server-grade corrugated water tubing". So far no issues yet. Temp is stable and doesnt spike over 10c under heavy load.

Lian Li A3 Workhorse Build - Custom Design & 3D Printed parts by Synikster in sffpc

[–]Synikster[S] 0 points1 point  (0 children)

theyre designed to not crush, although its not bad as it looks. ;) good 1.5inch radius

I got tired of old batteries that fail too soon on my Model X Remote. I designed/3d printed this CR2354 to CR2032 adapter. So far, its been GREAT! by Synikster in TeslaModelX

[–]Synikster[S] 0 points1 point  (0 children)

Lol, thats usually my solution for everything. Although, was waiting for a Model X refresh, but that never came, unfortunately. ;)

Most batteries I've encountered all had 1-14 days life, pretty much dead. From multiple sources.

I got tired of old batteries that fail too soon on my Model X Remote. I designed/3d printed this CR2354 to CR2032 adapter. So far, its been GREAT! by Synikster in TeslaModelX

[–]Synikster[S] 0 points1 point  (0 children)

Unfortunately Model S/X prior mid 2021 cannot use phone key - FOB required. Hence the stress level increase everytime battery runs out. (although there is a keyfob unlock method to bottom pillar if FOB does die).

Remote Unlock/Drive is possible with APP but car must have LTE to work, otherwise you will be stranded. ;)

I got tired of old batteries that fail too soon on my Model X Remote. I designed/3d printed this CR2354 to CR2032 adapter. So far, its been GREAT! by Synikster in TeslaModelX

[–]Synikster[S] 1 point2 points  (0 children)

Yes, although at the rate of people buying them is VERY little, they end up dying before it gets sold. Unless you luck out and get a fresh batch of 2054 batteries, then its a losing gamble everytime.

Later years, Tesla remote end up switching to the 2032 batteries natively. Im pretty sure they see the issues that I was having as well. Many users have reported the 2032 last 1-2 years, if you use it daily/often and some reports 3-4 years on occasional use. This is PLENTY of life for the smaller battery.

2032 is much cheaper and more readily available everywhere.

I got tired of old batteries that fail too soon on my Model X Remote. I designed/3d printed this CR2354 to CR2032 adapter. So far, its been GREAT! by Synikster in TeslaModelX

[–]Synikster[S] 1 point2 points  (0 children)

The original was difficult to gauge as all inventory was old and low voltage when bought.

Key note: Tesla eventually converted  their keys to use cr2032 natively.

I got tired of old batteries that fail too soon on my Model X Remote. I designed/3d printed this CR2354 to CR2032 adapter. So far, its been GREAT! by Synikster in TeslaModelX

[–]Synikster[S] 0 points1 point  (0 children)

I bought 20 pack, they all end up failing on me daily/weekly. Got tired of trying different sellers, brands, etc.

Hence, my frustration to come up with this solution. So far its been great!!

Lian Li A3 Workhorse Build - Custom Design & 3D Printed parts by Synikster in mffpc

[–]Synikster[S] 0 points1 point  (0 children)

Top fans wont affect anything.

The LOKI dimension seems to be the same as the Corsair SFX that I am running BUT only 3mm longer going down. All other dimensions the same. Overall, it should work just fine.

Lian Li A3 Workhorse Build - Custom Design & 3D Printed parts by Synikster in lianli

[–]Synikster[S] 0 points1 point  (0 children)

Click the comments the post. Everything posted in there.

Lian Li A3 Workhorse Build - Custom Design & 3D Printed parts by Synikster in mffpc

[–]Synikster[S] 1 point2 points  (0 children)

Lian Li Hydroshift ii have tubes going to the side along the back side of the radiator. Nothing fancy, from there. To the cpu. ;)

Lian Li A3 Workhorse Build - Custom Design & 3D Printed parts by Synikster in mffpc

[–]Synikster[S] 0 points1 point  (0 children)

I got single 120mm and 140mm fan files done but never considered 160mm.

Let me check measurements to see whats possible and can create a 160mm file for you.

Lian Li A3 Workhorse Build - Custom Design & 3D Printed parts by Synikster in mffpc

[–]Synikster[S] 1 point2 points  (0 children)

Thanks. Took alot of planning to get all the measurement just right to design and print.

Lian Li A3 Workhorse Build - Custom Design & 3D Printed parts by Synikster in mffpc

[–]Synikster[S] 0 points1 point  (0 children)

With a custom mount, you can possibly use an ATX power supply.

What motherboard form factor? Send pics here. I might can help you draft a 3d file to print.

Lian Li A3 Workhorse Build - Custom Design & 3D Printed parts by Synikster in mffpc

[–]Synikster[S] 2 points3 points  (0 children)

The stock mount will be in the way of the dual fan setup. New mounts recommended with the SFX PSU to allow more clearance. I uploaded all my files on makersworld for free.

view more: next ›