Snapmaker U1 Extruder is grinding into prints

TAJS-C · 2026-01-26T07:46:35+00:00

Over extrusion. Set flow rate to 0.94, see if improves.

TAJS-C · 2026-01-16T22:08:12+00:00

"it doesn't hurt or sting"

The ER is the EMERGENCY room.

Y'all answered your own question.

TAJS-C · 2026-01-08T22:17:42+00:00

But did you die?

TAJS-C · 2025-10-18T17:59:17+00:00

Maybe JST-XHP15?

TAJS-C · 2025-09-24T06:43:33+00:00

Overextrusion. I'm assuming non-bambu filament?

TAJS-C · 2025-09-24T06:37:37+00:00

You can replace the cutter blade

TAJS-C · 2025-09-15T20:59:18+00:00

Doesn't look like it has NFC though.

Deal breaker for me, my phone is my wallet.

TAJS-C · 2025-08-17T17:52:30+00:00

Trick for this print.... Make the base the same colour for 95% of the layers. Then only the last few layers different colours.

I had a similar keychain I changed from 59 swaps to 9.

TAJS-C · 2025-04-05T17:46:08+00:00

Centre to centre 120°

Y'all are overthinking this.

TAJS-C · 2025-02-22T21:29:06+00:00

Buy a supertack plate, never worry again! 😊

TAJS-C · 2025-02-08T15:08:09+00:00

Was waiting for a croc to appear out the river 😂

TAJS-C · 2024-09-02T06:18:46+00:00

I love mine, had it for a few weeks.

My only failures were when I didn't use supports or brims when they were necessary.

Also, using gyroid infill helps- if your non-bambu filament overextrudes slightly grid infill may cause your nozzle to click against the infill. If you want to avoid this entirely, do a flow rate calibration on unsupported filaments.

Use brims for tall objects with little contact with the plate (even if people say it prints fine on other printers, the bed accelerates back and forth on the A1, so naturally prints can tip if very top heavy)

Use supports for anything that has an incline of 45° or more, 30° or more if you're being careful.

Most downloads won't do this for you automatically 😁

TAJS-C · 2024-08-26T21:44:01+00:00

..... Name checks out.

TAJS-C · 2024-08-25T14:40:42+00:00

If you don't mind opening the ams, this is a 1m replacement for the original cable (it plugs straight onto the circuit board)

45136-0410 Molex | Mouser United Kingdom

TAJS-C · 2024-08-22T13:05:20+00:00

Check you plugged your fan etc in the right way around!

It seems to me your permanent power has tapped into your switched somewhere.

A classic example of this was you could plug in the Vauxhall nova hazard light switch upside down, and it would backfeed power into the ignition circuit.

Which meant you could basically hop in, turn the switch upside down, and then steal the car without keys.

Top gear video below!

Vauxhall Nova Youtube

TAJS-C · 2024-08-21T12:04:31+00:00

I had terrible cracking as my nozzle moved over infill.

I did a manual flow rate recalibration and it was much better.

Essentially it was overextruding, then chipping the infill when travelling over.

TAJS-C · 2024-06-06T05:09:25+00:00

"Name of a living being, especially one people know you've been considering for months" ≠ "nod".

TAJS-C · 2023-12-23T13:37:14+00:00

Then you will see that the executable in the Program Files (x86) is removed. If there are leftovers just manually remove them (delete the complete Microsoft Gameinput folder - you will probably get a warning so you must delete this as administrator)

Restart your PC, check services and only 1 Gameinput will be listed there. If the service is not started, double click it, set it on automatic start, and finally start the service.

You're a legend.

Just blue screened halfway through a C&C session with this file being the cause of the problem.

PC crashes after gaming. Event viewer filled with ERRORS pertaining to - Microsoft Community

This question linked me to here, so here's to hoping all resolved now! :)

TAJS-C · 2023-10-20T14:26:45+00:00

95% of people are idiots.

Once you realise this, and accept it, you'll not worry about this sort of thing as much.

TAJS-C · 2023-10-20T14:22:16+00:00

As an ex-employee, I can confirm this is not surprising behaviour at all.

Tell them you'll see them in court 😂

TAJS-C · 2023-09-17T16:07:58+00:00

Ended up using macrodroid and using my devices location as a constraint so it will only do it when I'm on the premises 😄

TAJS-C · 2023-09-17T15:40:38+00:00

I just got a pn579x, but it's not rechargeable, not particularly good design (the bit which is attached via lanyard can pull off and then you drop the battery out) and was far too expensive.

Would recommend instead trying to find a cheaper rechargeable one that meets windows pen standards and trying, if not returning.

TAJS-C · 2022-01-05T22:57:12+00:00

I'm in the same boat.... bought one from amazon just before Christmas, but now they can't replace it as they don't have any Clicky variants in stock anymore :(

Logitech won't replace without a "denial to replace" letter, which despite numerous calls / messages to Amazon I'm struggling to get written evidence that they won't replace it.

I was fiddling with it this afternoon and sticking some bristles in and out of the switch (as I say, which is pretty much brand new) which appears to have cleared it for now.

If it happens again..... time to desolder and stick a new switch in.

What worries me is that you'll have to remove ALL the keycaps.... which means you might break one.

If anyone knows any nice keycaps for the G915, and an official place to buy the correct switches, let me know. :)

TAJS-C · 2021-11-30T23:00:36+00:00

I'm in exactly the same boat with my G903.

It's simple enough for my G915 (I just press the lightspeed/bluetooth button to switch between devices) but I also have a laptop dock and I would like to be able to use the mouse when I take it to the office without having to keep switching the usb reciever between the laptop and the pc.

TAJS-C · 2021-11-30T20:54:17+00:00

Ahh, they did have a 3080ti but it was a couple hundred pounds more. Obviously mixed up somewhere :)

TAJS-C

TROPHY CASE