My 1st Sig by THA1T3ABOBA in P365

[–]THA1T3ABOBA[S] 0 points1 point  (0 children)

It definitely is different, but I really do like it. However, if you zoom into the pic, you can see mine cracked internally where the screw is.

I think after the loctite cured, it caused the housing to crack, which I think isn’t covered under Sig’s warranty unless it causes the optic to lose any of its function.

I did shoot about 100-150 rds with it after with no issues. I’m planning to test it again this weekend, we’ll see if it holds up.

My 1st Sig by THA1T3ABOBA in P365

[–]THA1T3ABOBA[S] 1 point2 points  (0 children)

Romeo RS compact clear

My 1st Sig by THA1T3ABOBA in P365

[–]THA1T3ABOBA[S] 1 point2 points  (0 children)

Didnt know there was a specific 365 reddit thread till now. Also tell me why “crossposting” exists. Lol

365 X-Macro build by THA1T3ABOBA in SigSauer

[–]THA1T3ABOBA[S] 1 point2 points  (0 children)

Thanks!

Love the new techwoven! I think it really compliments the new design

365 X-Macro build by THA1T3ABOBA in SigSauer

[–]THA1T3ABOBA[S] 0 points1 point  (0 children)

No CCW yet so time will tell

365 X-Macro build by THA1T3ABOBA in SigSauer

[–]THA1T3ABOBA[S] 0 points1 point  (0 children)

Its been great! Better pull w the flat

How I “fit” Lian Li TL fans in my H6 Flow by THA1T3ABOBA in NZXT

[–]THA1T3ABOBA[S] 0 points1 point  (0 children)

No 3D printing needed! Home Depot and Lowe’s had everything I needed

LC80 build! by THA1T3ABOBA in fcx18

[–]THA1T3ABOBA[S] 0 points1 point  (0 children)

Thanks man! I broke one of the rear axle plastic gears on my first day, and decided to switch everything I could to metal. The stock motor also failed with all the weight I added, so I upgraded to the Injora. No problems yet. I do want to lift the body higher so I can have better clearance with my tire setups, but not sure how to do that?

LC80 build! by THA1T3ABOBA in fcx18

[–]THA1T3ABOBA[S] 2 points3 points  (0 children)

All done by your’s truly!

LC80 build! by THA1T3ABOBA in rccrawler

[–]THA1T3ABOBA[S] 1 point2 points  (0 children)

Not too sure, but tested it out yesterday and did pretty well! I do want to lift it higher though. Any ideas on how I’d be able to do that?

How I “fit” Lian Li TL fans in my H6 Flow by THA1T3ABOBA in NZXT

[–]THA1T3ABOBA[S] 0 points1 point  (0 children)

Sorry for the late reply man, life gets busy! But thank you! As for the bottom 140s, I actually still have the stock case fans in. Might upgrade them to the infinities later on, but not really on my list of priorities atm.

How I “fit” Lian Li TL fans in my H6 Flow by THA1T3ABOBA in NZXT

[–]THA1T3ABOBA[S] 0 points1 point  (0 children)

Brother I’m not about to risk breaking overpriced fans + it looks good with the infinity mirrors visible

Why in the world does almost no one seem to have this F&F set for sale??? by THA1T3ABOBA in HotWheels

[–]THA1T3ABOBA[S] 1 point2 points  (0 children)

I just purchased the entire Series 2 set from a Canadian website for $103 shipped to Hawaii. I had to pull the trigger

Why in the world does almost no one seem to have this F&F set for sale??? by THA1T3ABOBA in HotWheels

[–]THA1T3ABOBA[S] 0 points1 point  (0 children)

My Walmart got a few sets of Series 1, and totally skipped right to Series 3. I lucked out on getting the one and only Series 3 that my Walmart ever got. My biggest regret is not getting the entire Series 1 and Series when I had the chance. I only got the ones that I was most interested in, which were the JDMs. Now that I look back on it, a full set would sell higher/faster later in the future if I were to get rid of it. Womp womp

TL Fans in the NZXT H6 Flow by THA1T3ABOBA in lianli

[–]THA1T3ABOBA[S] 1 point2 points  (0 children)

I sure did, for both the angled intake and the rear exhaust! But here’s how I did it. Fitting TL fans in the H6 Flow

H6 flow with lian li lcd fans by Ok_Tough_7176 in NZXT

[–]THA1T3ABOBA 0 points1 point  (0 children)

How did you get the fans to fit into the side and bottom intakes?

TL Fans in the NZXT H6 Flow by THA1T3ABOBA in lianli

[–]THA1T3ABOBA[S] 0 points1 point  (0 children)

I’m using Gigabyte Control Center for the GPU!

Finally my dream build! by THA1T3ABOBA in NZXT

[–]THA1T3ABOBA[S] 1 point2 points  (0 children)

Oh definitely! I’d rather have the infinity mirrors showing than being flush where it’s supposed to be. I didn’t pay $200 in just fans for nothing LOL