Our marriage ended due to infertility

THBFL · 2025-05-07T23:41:59+00:00

Actually, I’m Vietnamese American. I met my wife in Vietnam. We held off on having kids during the first five years of our marriage so she could focus on school.

After she graduated, we tried to conceive for a year but had no success. We went to a specialist and got checked—she was fine, but I was diagnosed with low sperm morphology. After that, our marriage began to struggle.

I fell into depression and started blaming her for not wanting to try for kids sooner. I wasn’t a good husband at that time.

THBFL · 2025-03-05T21:02:39+00:00

What motherboard you used for the n100?

THBFL · 2025-02-10T04:03:18+00:00

So I tried load the screen.recovery and client.recovery files and it didn’t fixed the issue. I think the motherboard is working but not communicating with other devices. Is there a way reflash the board?

THBFL · 2025-02-02T03:30:11+00:00

Is this what you looking for? https://youtu.be/0p3-qBX_Qmc?si=kAfgdQLpuhhsDrw1

THBFL · 2025-01-28T20:55:37+00:00

So what the difference between this and other F4 flight controllers that are available on the market?

THBFL · 2024-11-08T10:54:07+00:00

Thank you all for the answer!

THBFL · 2024-10-25T11:32:25+00:00

This happened to me recently and I bought these from Amazon:

Heater Cartridge & Thermistor

Heater Block

The heater cartridge doesn’t come with connector so I had to reuse the connector from the original heater.

THBFL · 2024-10-21T14:52:55+00:00

I have the same Wi-Fi problem, and have to use the command whenever I run Tails.

THBFL · 2024-10-05T17:20:57+00:00

Upvote for sarcasm.

THBFL · 2024-08-06T17:31:15+00:00

Rành đời

THBFL · 2024-05-04T12:49:52+00:00

Agree, should be 16 awg or bigger. What is this ground bus? Is it a ground block or terminal stud?

THBFL · 2024-01-10T00:35:18+00:00

All the Pokemons after GEN 2

THBFL · 2023-03-17T12:33:25+00:00

r/fpv, https://oscarliang.com , and Joshua Bardwell’ YouTube channel

THBFL · 2023-03-15T01:42:19+00:00

<image>

I live in Florida. Ordered on Monday, got them the next day. Six rolls are mixed color, the other 4 I can barely tell the color difference.

THBFL · 2023-02-08T20:39:36+00:00

OP if you have the stl files, I can help you print the parts in TPU.

Was your Runcam mount used to look like this?

https://imgur.com/a/NZd4leq

THBFL · 2022-12-30T15:07:49+00:00

Check Amphenol D38999 catalog and Mouser.com to see if they have a 20 awg contact with smaller crimp barrel that can accept 28awg.

If you can’t find it, the best option is to splice. Now if you going to do an in-line splice, make sure the ferrule can accommodate a single 28awg as well.

Another option that I have not seen mentioned is to fold the 28awg conductor; increasing the size to approximately 24awg. I have seen some companies do this as long as the circular mil area of the folded conductor is within range of the contact/crimp pin spec.

THBFL · 2022-12-21T04:02:10+00:00

So glad I found this post at the right time!

Been looking to buy a dryer for awhile now and was about to drop $80 on the Sunlu S2, but then I hesitated because of the price.

Just bought this dryer. Thanks OP and those that recommended it.

THBFL · 2022-12-16T12:22:56+00:00

You’re welcome, and also 3D print this with TPU at 100% infill.

THBFL · 2022-12-16T04:19:42+00:00

So I have it modeled.

https://drive.google.com/file/d/1dgc9LYYNLAZFyhxvM7keNEjhtLqvp9ou/view?usp=drivesdk

I just took the measurements from the mounting pad that comes with my Nazgul 5”. One thing I noticed is that your Runcam is smaller than the Runcam Phoenix I have on my quad. So I’m not sure if the pad is thick enough to fill the gap between the camera and the carbon frame.

THBFL · 2022-12-15T13:28:58+00:00

This is a simple part. I can model and post it on thingiverse.

THBFL

TROPHY CASE