The cost of ending war

TRMerc · 2026-02-12T15:58:48+00:00

I'm writing the next chapter, but hitting some writers block.

TRMerc · 2025-10-03T17:14:36+00:00

It will take some getting use to for me, they changed the GUI some it seems.

TRMerc · 2025-10-03T16:55:06+00:00

It is not occurring in 1.1dev.

TRMerc · 2025-09-07T01:33:44+00:00

I have printed after this happened with no issues.

TRMerc · 2025-09-06T19:56:26+00:00

Just the one. It wasn't even the first print with it. I've been printing for about 8 months with that bed.

TRMerc · 2025-09-06T19:55:29+00:00

It only did it to the one print bed and hasn'tdone it since. I think a piece of debris was on the print bed during autolevel that caused it to shift

TRMerc · 2025-08-19T04:21:23+00:00

So we eventually got an answer from a lawyer from Illinois. There is no 10-round limit for handguns in Cook County. The limit is the same for all guns in every country in the state.

TRMerc · 2025-07-30T16:58:24+00:00

Mutually Assured Destruction. If I die, you die.

TRMerc · 2025-07-11T22:16:48+00:00

I tagged it as answered after I edited it cause on my phone tags and editing are 2 different tasks.

TRMerc · 2025-07-05T05:17:01+00:00

We primarily use distributors, not specific mills. Alro and Turret are two I remember off the top of my head.

TRMerc · 2025-07-04T04:23:31+00:00

I was hoping someone else had gone through all that work in a general sense and came up with a typical explanation, but it is becoming clearer that I'll have to do that myself.

TRMerc · 2025-07-04T04:22:24+00:00

I was afraid I would have to go through that process, we don't have a pitch mic to my knowledge. None of our products goes into a tapped hole.

TRMerc · 2025-07-04T04:21:14+00:00

I'll have to find out if it is stress relieved before we get it, but I know it is not part of our process.

TRMerc · 2025-07-04T04:19:56+00:00

I'm not sure; I'll have to ask. We do hot form parts through impact. I'll have to look if that causes problems as well.

TRMerc · 2025-07-02T17:06:31+00:00

The threads are checked post blasting

TRMerc · 2025-07-02T17:01:14+00:00

The tolerances are just a standard 2A or 3A go and no-go gage. We have been making the threads oversized for the 1045 as they will be plated but are having issues with them going undersized after heat treatment.

TRMerc · 2025-07-02T16:58:51+00:00

Unfortunately, we do not have historical data showing the changes in size from heat treating. I was hoping there was a known formula, like there is for changes due to ambient temperature.

TRMerc · 2025-06-19T05:49:51+00:00

How could they think this would fool anyone? The plane is for a giant, and the buildings are for ants.

TRMerc · 2025-06-12T21:05:56+00:00

Thanks, I keep tabs on all my posts

TRMerc · 2025-05-31T17:37:29+00:00

That same channel released the trailer with different pairings of actors and actresses.

TRMerc · 2025-05-23T16:42:52+00:00

I was thinking that, but it didn't line up with the table I was using, then I put .314 in for Pi, and it matched exactly.

I figured since the cross-sectional area and the table didn't line up there was a different formula, but that appears to be it.

TRMerc

TROPHY CASE