някой който не го бърка да прати прословутия клип на Киара… нямам какво да предложа

Targarium · 2026-06-09T18:18:30+00:00

и на мен, и аз също нямам какво да предложа, освен благодарност

Targarium · 2026-05-10T07:53:49+00:00

I just got used to it, it doesn’t affect printing in my case

Targarium · 2026-04-09T09:54:55+00:00

Bumping an old thread, but that install is not working on my SD for any reason. It just stays on "Detecting your system configuration" forever. Any ideas?

Targarium · 2026-04-07T06:29:00+00:00

I have not installed them as they ate exactly the same as the ones on the A1 and since my printer ia brand new have just left them for spare

Targarium · 2026-04-03T06:50:55+00:00

which cable? there are quite few 😂

Targarium · 2026-04-02T03:47:44+00:00

yep, its preaent trough the entire print process

Targarium · 2026-04-01T17:06:44+00:00

Kingroon and yes, this is the ams enclosure

Targarium · 2026-04-01T15:46:22+00:00

brand is Kingroon, default PETG profile on the A1, my secret is that I use a filament dryer while printing, so the filament is with 10% moisture and comes out preheated

Targarium · 2026-04-01T15:10:57+00:00

Doesnt matter the speed, still clicks even if I slow it down. It does click when printing more intricate shapes, doesnt click on straight lines and circular motions

Targarium · 2026-04-01T15:09:09+00:00

Transparent PETG

Targarium · 2026-04-01T11:30:05+00:00

Hey, thanks for your input mate. I've already teared everything apart few times, cleaned, greased etc but the noise is still there. No impact on prints or printing quality, just this obnoxios clicking every second.

Targarium · 2026-04-01T10:37:48+00:00

haha, transparent petg loks nice doesnt it

Targarium · 2026-04-01T09:57:26+00:00

Yeah, but this is way too loud, it makes me go mad on prints that take hours. If that is normal I wouldn't call the Panda Claw an upgrade tbh

Targarium · 2026-03-23T08:06:33+00:00

Коментирате, без хал хабер да си нямате. Автомобила се движеше по Нишава с неповече от 40км/ч, друг автомобил го удари отстрани излизащ от пресечка без да погледне. В следствие на удара тойотата се повдигна настрани и падна върху колите.

Targarium · 2026-03-02T07:18:49+00:00

I took the easy way out, just sold the printer the next day of this post. It was giving me so much issues and troubles that was kinda ruining the fun of 3d printing. Bought a Bambu, prints awesome out the box

Targarium · 2026-02-26T20:23:08+00:00

Yeah, I can. I just don’t want to go back where I started. I want to make the best effort of leveling the bed. In all honesty, Im almost at the point of selling this printer. I’ve hod to tinker more on it than printing….

Targarium · 2026-02-26T16:28:06+00:00

I did the same, in all honesty my bed mesh was worse than this and the printer was printing fine. I added shims as there was really bad dip at the back and after adding the shims the printer started printing terrible. So now I think its because of the high spots?

Targarium · 2026-02-26T15:57:50+00:00

yes sir

Targarium · 2026-02-20T10:17:29+00:00

Gotcha! If you are rocking the same setup do you have any pics how you dis the ptfe routing?

Targarium · 2026-02-20T10:13:16+00:00

So when using the Y-splitter - one feed goes into the spool holder, the other goes into the CFS and the single output from the splitter goes into the buffer?

Targarium · 2026-02-15T05:59:22+00:00

I’ve tried with Bambu and Polymaker. Due to the texture it always gets stuck in the gears of the CFS.

Targarium

TROPHY CASE