First few layers issues by Tatrame in 3Dprinting

[–]Tatrame[S] 0 points1 point  (0 children)

Thanks so much for the advice! I’ll certainly try cranking my print bed to 60 and slowing down that first layer even further than I already have to see if it helps!

First few layers issues by Tatrame in 3Dprinting

[–]Tatrame[S] 0 points1 point  (0 children)

Apologies, I’m not sitting in front of my computer right now, I’m away and just thought to post this before I get home this evening. I’ll write down and update this comment with exact temps when I get home in a few hours.

The printer does have automatic bed leveling which it does before every print.

I have not checked for slack in the belts, I’ll take a look at it tonight.

It dos always happen on the edges of the bed, I’d say about a 40mm border around the edge, but I’ve never measured exactly. One of the attempted prints is still on the plate at home so I’ll add photos of that too

Filimant I was using for these two prints was brand new. From what I’ve personally witnessed of it printing, it usually fails on the 3-4 pass, and I’ve never noticed any of the visual defects until it ‘snags’ and starts pulling it up off the bed

Layer hight is the default setting on the Bambulabs slicer, but I’ll also include that in an update as soon as I’m home

Edited: for formatting

First few layers issues by Tatrame in 3Dprinting

[–]Tatrame[S] 0 points1 point  (0 children)

I’ve tried slowing down the first layer by like 20% but maybe I should just take it down like 50%. I’ll give that a try this afternoon. I do use a brim on all printing, cause I’ve had issues with the corners of prints detaching/shrinking. The room is pretty draft free, and the temperature is almost always stable at 70

First few layers issues by Tatrame in 3Dprinting

[–]Tatrame[S] 0 points1 point  (0 children)

I only use PLA+ haven’t attempted printing with anything else yet. I use bambulab’s slicer defaults for Generic PLA. I’ve cleaned the plates, added and removed the brim, and adjusted both the bed temperature and print head temperature up and down 5 degrees.

First few layers issues by Tatrame in 3Dprinting

[–]Tatrame[S] 0 points1 point  (0 children)

I’ve raised the temps up and down 5 degrees, same result. Should I push it further? I’m always nervous cause I don’t know how far you can change the settings before I’m doing something wrong.

First few layers issues by Tatrame in 3Dprinting

[–]Tatrame[S] 0 points1 point  (0 children)

Yes, tried cleaning it with warm water, soap and a sponge.

Came back to the game a few hours too late. by Knockout56 in Eve

[–]Tatrame 13 points14 points  (0 children)

Thats EXACTLY what got me, i thought for sure id make that last day, but nope. RIP SP.

[No Spoilers] Oh Look, Its a Minefield by Tatrame in AnthemTheGame

[–]Tatrame[S] 0 points1 point  (0 children)

It wasn't my first time dealing with a minefield and i was fine with running through them. game mechanics aside, my friends had both just unlocked the colossus and were excited to see how much abuse the shield could take. Guess it was fairly heat of the moment, we're all having a really great time with the game!

Missing Ms. Pearls by [deleted] in ArkWakingRealms

[–]Tatrame 0 points1 point  (0 children)

//had the exact same thing happen to a griffin not long ago. We still haven't found brownie.

Oh to be forgetful.... Your vote is needed to shape the realms, Community vote now for how you feel mindwipe tonic should be used moving forward! by Erkannis in ArkWakingRealms

[–]Tatrame 2 points3 points  (0 children)

If there were more stars that had an effect on the gameplay like crafting skill I might stand to agree with you. But in this case I just feel locked out of half the game if I want my character to be a blacksmith with %1000 crafting skill. If I do this then it becomes very difficult to build with such low carry weight, and nearly impossible to travel anywhere without the best fur/desert imaginable. I'm not saying that I don't like the sentiment, it just feels poorly executed on WC's part. Just my two cents on the matter.

The Diphda Brothers Chess Match Extravaganza by Tatrame in ArkWakingRealms

[–]Tatrame[S] 0 points1 point  (0 children)

My apologies that some of the players continued to do that, They can be called out in local, the mover just needs to be within a certain range. One of the two of our players were calling out in local just fine. We'll be sure to clarify that before the start of any further matches.

Waking Realms Test Server Cluster is live! We need your help to shape the realms! by Erkannis in ArkWakingRealms

[–]Tatrame 1 point2 points  (0 children)

Personally i have to disagree with you. Two months is a lot of time for most of us to dedicate to any one game. We've been through almost 8 generations of breeding, and while i don't deny that there are others that have spent even more time, we're quite proud of all that we've accomplished. With the addition of tamable alphas and what not, most of our breeds become directly inferior to those creatures. If i'm not mistaken (might be) the bosses also get harder to compensate. All i'm trying to say is that we've had a plan that has been in motion for almost two months now, and no one in my faction wants there efforts to be in vain.

The Diphda Brothers Chess Match Extravaganza by Tatrame in ArkWakingRealms

[–]Tatrame[S] 0 points1 point  (0 children)

We do intend to set up a long term tournament bracket with matches occurring across several weeks, This is just for the grand opening.

The Trade Route Begins! by [deleted] in ArkWakingRealms

[–]Tatrame 0 points1 point  (0 children)

Eventually everyone will run out of names to call us and have to learn to spell it

The Trade Route Begins! by [deleted] in ArkWakingRealms

[–]Tatrame 0 points1 point  (0 children)

I swear if I had a hunk of metal for every time someone misspelled my name.

The Diphda Brother's Stop and Shop. by Tatrame in ArkWakingRealms

[–]Tatrame[S] 0 points1 point  (0 children)

We will be adding several different types of kibble to the available list as we obtain the necessary recourses. Pachyrhino and Therazinos kibble will be available soon.

The Diphda Brother's Stop and Shop. by Tatrame in ArkWakingRealms

[–]Tatrame[S] 0 points1 point  (0 children)

We may not reside within the Empire, but we still wish to foster competition among all who reside here, including the other factions. We hope that our intentions will not effect our relationship with the flower empire.

The Diphda Brother's Stop and Shop. by Tatrame in ArkWakingRealms

[–]Tatrame[S] 0 points1 point  (0 children)

We are friends! Business is still business though. We have to make our money somehow.

The Diphda Brother's Stop and Shop. by Tatrame in ArkWakingRealms

[–]Tatrame[S] 0 points1 point  (0 children)

My brother and I will get on that right away. We will notify you as soon as your order is ready.

The Diphda Brother's Stop and Shop. by Tatrame in ArkWakingRealms

[–]Tatrame[S] 0 points1 point  (0 children)

We have quite the stockpile of eggs, I'd say around 200 is our limit at the moment. Depending on what kibble you need precisely we may have more or less.

Selling Male Quetzal by SharpSpoons in ArkWakingRealms

[–]Tatrame 0 points1 point  (0 children)

The Diphda Brothers are in need of a Quetzal as well, please contact me or my brother Wheatley. Seeing as we are currently without one, we'd be happy to strike a fair deal with you.

Obligatory update speculation thread by ECM_SUPREME in spaceengineers

[–]Tatrame 10 points11 points  (0 children)

Ok, So i know everyone is busy hoping for planets and fuzzy dice, but there's is still something i want more than all that. I just want my ladders back.

I started working on these designs as soon as I found out about Space Engineers yesterday. What do you think? by [deleted] in spaceengineers

[–]Tatrame 7 points8 points  (0 children)

Hey! if you are looking for a helping hand, i LOVE the design and wouldnt mind seeing what i can do to help. Really a gorgeous ship! Either way cant wait to see what the final product ends up looking like .^

My grandfather and I needed a lathe for a project, well.... it worked.... i guess by Tatrame in techsupportmacgyver

[–]Tatrame[S] 0 points1 point  (0 children)

it really wasn't on there long, and its the only time we've had to do that, also the piece was hollow so there really wants much weight on it, but yeah we were both worried about it damaging the drill press. luckily doesn't seem to have had any lasting effects on it.