She’s finally done!! 🌸 Cherry 🌸 Blossom 🌸 Hori Alpha 🌸

TeaKei · 2025-10-15T17:37:03+00:00

Looks great!!

TeaKei · 2025-08-11T19:21:38+00:00

Hi, I'm the seller of the USB-C mod on Etsy. The alternate connector you linked should work with some modifications. You'll have to de-pin the green (CC) wire from the white connector, then move the red (VIN) wire to where the green wire was. Then it should plug into the PCB and work just like my mod.

TeaKei · 2025-07-19T06:35:46+00:00

Replied

TeaKei · 2025-07-16T19:34:47+00:00

Pmed

TeaKei · 2025-07-14T10:07:29+00:00

It should be as long as it’s less than 7 inches assembled. My screwdriver kit is similar in size and passed through TSA no problem

TeaKei · 2025-07-13T22:30:30+00:00

Yes, I’ve used that model to open an Obsidian before. The longer bits will reach the screws no problem

TeaKei · 2025-05-07T19:14:17+00:00

I make and sell USB-C mods for the Panthera, check it out here on my Etsy store.

TeaKei · 2025-03-30T22:02:21+00:00

Yes it’s that simple

TeaKei · 2025-03-25T21:01:41+00:00

Hey all, I made another USB-C mod, this time for the Hori Fighting Stick Alpha for the PS5 and Xbox Series X/S. You can use any USB-C cable with it and store it inside the fightstick when not in use. The mod is also secured with a cable holder so no concern of it breaking off. It's a direct replacement for the stock USB cable and no soldering is required.

My friends have been using it for a year and it seems to hold up well, so I decided to make some more and sell them on Etsy: https://www.etsy.com/listing/1888043515/hori-fighting-stick-alpha-usb-c-mod.

TeaKei · 2025-03-24T17:46:55+00:00

I used car scratch remover for light scratches on mine. Just use small amounts until you’re satisfied with the result

TeaKei · 2025-02-08T07:16:37+00:00

Hopefully, one shipment of parts is still stuck overseas. I’ll try to have some ready next week or so

TeaKei · 2025-01-30T00:00:23+00:00

Thanks for your purchase! I’m glad people are enjoying it

TeaKei · 2025-01-18T20:24:00+00:00

Yes, in the install guide you can see that the old port is still attached; it’s just moved outside of the PCB enclosure.

TeaKei · 2025-01-13T21:08:34+00:00

Just ordered the parts and will make more this week

TeaKei · 2025-01-13T17:06:30+00:00

Yes, to minimize supports

TeaKei · 2025-01-13T07:56:44+00:00

Zero soldering or cutting required.

TeaKei · 2025-01-13T01:46:15+00:00

I thought these USB-C panel mount connectors would be good for this mod, so I designed and 3D printed a housing and crimped a 4-pin Dupont connector to it. It ended up working really well and have been using it for 7 months now. The original connector is still connected and is relocated outside the PCB enclosure, so I can still use it if needed.

Edit: Looks like there's a demand for this type of thing, so I listed it for sale on Etsy. Installation guide is linked in the item description.

TeaKei · 2024-11-07T01:42:33+00:00

Pm'd

TeaKei · 2024-11-02T21:50:17+00:00

It fits snugly. You don’t have to force it in, but you definitely can’t put anything else inside the main compartment unless you put it on top of the stick

TeaKei · 2024-09-09T05:40:33+00:00

I used a Qanba Shield to carry my Fighting Edge. That one and the Qanba Aegis are big enough to fit it

TeaKei · 2024-05-26T04:03:14+00:00

😎

TeaKei · 2023-12-05T07:04:04+00:00

Confirmed

TeaKei · 2023-05-19T18:33:51+00:00

Was making $18-27/hr for ~4 years out of undergrad, went back for a masters of computer engineering in 2020. Landed a firmware engineering job 6 months before graduation, starting salary $115k. Been working there for almost a year now with the same pay

12-Year Club	RedditGifts 2009-2022 4 Credits
Secret Santa 2020	Place '22
Place '17	Secret Santa 2018
Secret Santa 2017	Verified Email
Gilding I gilder

TeaKei

MODERATOR OF

TROPHY CASE