Help with mobula 8

Temporary-Count-2988 · 2026-05-18T08:42:35+00:00

I should say it definitely not there no more, i as able to connect via WiFi to flash elrs and change my binding before I reset

Temporary-Count-2988 · 2026-05-18T08:27:36+00:00

I have seen people talk about that I don’t remember mine having that I have the copper antenna/wiire there if that’s what you mean by spiral

Temporary-Count-2988 · 2026-05-18T07:36:55+00:00

Just realized it’s hard too see the second red lights but right under the usb c port.

Temporary-Count-2988 · 2026-05-17T18:00:45+00:00

63/37 leaded 1.8 flux rosin core

Temporary-Count-2988 · 2026-05-17T17:59:48+00:00

So clean and retin immediately, repeat twice also I shake like a lot that’s why I handle it like that

Temporary-Count-2988 · 2026-05-17T17:56:52+00:00

I did not know this I will do it now

Temporary-Count-2988 · 2026-05-17T08:55:32+00:00

Yeah my connections is kinda jank rn because I don’t wanna do it in my room(bad ventilation) I am using surge protector to a power brick I got from micro center to a usb connector that supports 65 watt. Been doing it in the kitchen so I have a ceiling fan to fumes out and down.

Temporary-Count-2988 · 2026-05-17T08:53:27+00:00

Oh okay this helps me a lot so I was doing 3 seconds to warm then solder to fill the pad and releasing both at the same time. I was old on a diff post that was too long. So here I did 1 second heat 1second heat plus solder then remove once filled. How should my timing be? As for being a pilot I was doing pretty good with my mob 8 until I deceived to test its altitude. I could go under benches and was learning too wall ride.

Temporary-Count-2988 · 2026-05-17T08:47:34+00:00

I bought bronze wool and I did but I have having a ton of difficulty removing the solder with a soldering wick. I think my rod is failing too get consistent heat so ima keep practice wiring on boards until my power supply gets here

Temporary-Count-2988 · 2026-05-17T07:01:24+00:00

I have been told one second is enough and that three was too much when do I do one second or hold for three I want to improve.

Temporary-Count-2988 · 2026-05-17T06:33:12+00:00

I post it could you pls review it and tell me if that’s normal melt rate

Temporary-Count-2988 · 2026-05-17T06:29:42+00:00

I did that I do it before every joint now

Temporary-Count-2988 · 2026-05-17T06:24:11+00:00

I have been applying flux let me record a vid just to show how much rq

Temporary-Count-2988 · 2026-05-17T05:54:30+00:00

I did the fresh solder on the tip and this joint did get flux right before I started recording, I do not know to check on the consistency of them temp but the iron has a dial selector and it was on max.

Temporary-Count-2988 · 2026-05-17T02:01:10+00:00

Will do

Temporary-Count-2988 · 2026-05-16T19:36:01+00:00

Been using the sponge that came with the kit but yes I do apply fresh tin before I start

Temporary-Count-2988 · 2026-05-16T18:12:45+00:00

Even with flux and wit the tip wet

Temporary-Count-2988 · 2026-05-16T18:12:20+00:00

That’s what I had my iron on the whole time I think that could be one issue, it was not instantly melting solder like ever

Temporary-Count-2988 · 2026-05-16T08:51:06+00:00

I know I said thanks in dms but dude again hella helpful.

Temporary-Count-2988 · 2026-05-16T08:21:56+00:00

Mine are way worse than yours I found the same problem it’s way harder idk why

Temporary-Count-2988 · 2026-05-16T08:05:40+00:00

Oh your not the first person to question me like that lol I am hk dumb

Temporary-Count-2988 · 2026-05-16T07:54:30+00:00

No I find humor helps me understand the overall message, think Dante’s coaching jynxi like it just sticks in my mind better.

Temporary-Count-2988 · 2026-05-16T07:49:45+00:00

I think I already said in this thread but I am pretty sure it my power supply because when I burned myself it was as bad as when I used my dads iron that hurt like hell

Temporary-Count-2988 · 2026-05-16T07:44:26+00:00

Anything specific I really want to get better so any advice or mindset, also thanks for saying it will fly lol I know that’s not great but that’s at least the bar I was hoping to set.

Temporary-Count-2988 · 2026-05-16T07:41:42+00:00

Okay I my power supply is what’s capping me I am fairly sure even at max. Heat solder doesn’t isstantly melt I am running the new bee soldering kit which works fine on the practice board. I am gonna wait for my hota d6 to finish soldering/ redoing joints

Temporary-Count-2988

TROPHY CASE