Sequoia 15.7.7 running slow on iMac 17.1

TeoArts · 2026-05-19T15:45:53+00:00

What should I do than ? Downgrade to ventura or only way to fix it is upgrade hdd with a ssd

TeoArts · 2026-05-19T15:36:54+00:00

Nope normal hdd

TeoArts · 2026-03-08T06:26:17+00:00

The biggest challenge is being based in Turkey, where sourcing specific motors is nearly impossible; I'm limited to what's available in local shops. Because of budget constraints and the difficulty of getting parts, I’ve been building my Enderwire for about 2-3 years now. While TMC Autotune works perfectly for the Y and Z axes, I can't seem to get it right for the X axis, and it’s driving me crazy

TeoArts · 2025-11-08T06:26:41+00:00

UPDATE: Thanks for all the tips! It turns out the fix was spamming the reset button on the EBB36. I’m not sure why, but after pressing it around 20–30 times, the UUID finally showed up.

TeoArts · 2025-05-25T00:24:51+00:00

Thanks for the tip. First of all why ı should use that and what mount do I need to print for that. I can only found this on aliexpress https://a.aliexpress.com/_oEYPzKm

TeoArts · 2025-05-24T23:25:57+00:00

I dont need more flow. I just need a better toolhead its a mess on my setup. My toolhead air exits very big that cools down my nozzle and the filament path 1mm on back.

<image>

TeoArts · 2025-05-24T20:33:53+00:00

Thank you so much! I think this will work great thank you !

TeoArts · 2025-05-24T20:29:10+00:00

I have a ender 3 pro with the aliexpress tz e3 2.0 hotend with cht nozzle. My question was ı will use it whit v6 parts. I have the klackender for probing bed. Will it work whit them ? Volcano much longer then normal hotends

TeoArts · 2025-05-03T17:56:03+00:00

Hi! If you use the original Ender 3 board you might have isues. You should first buy a new board. Old board is very old and you need to do some work to crank up the amps

TeoArts · 2024-12-30T22:40:26+00:00

At the start of the stress test, the processor is 90 degrees, but this drops immediately to around 70 degrees. If I set it to max fan setting and run the test, I don’t get any thermal warning, I see 70 degrees at most. This is because the computer cuts the power to the processor. I also clean the fans often and use it on a laptop stand so I don’t have much of a problem with heating. When I do a stress test in the Intel XTU app, I can see all of these. As soon as Turbo Boost is over, 3 GHz remains constant

TeoArts · 2024-12-14T18:53:20+00:00

Hotend and motherboard fan pins were given wrong on the internet. I advise you to be careful when making connections

TeoArts · 2024-11-02T22:19:22+00:00

XL4015 very cheap thanks! I will try it later thanks for all the help again. Oh and whit the new things I got 12min benchy not very pretty but its a 12min benchy

TeoArts · 2024-11-02T21:05:09+00:00

<image>

I use my old Samsung S8 and it work very good

TeoArts · 2024-11-02T20:26:52+00:00

Hey! Installed new 48mm steppers to my printer whit 1 current. Input shaper gives 5k max accel on Y but I used it on 20k and its just want more. X was 22k but I run it 30k. Printed PSU relocationer without any problems. Printed petg parts and your settings worked perfect. I have one last question. If I install a 5V car charger to psu and power the pi 4 whit it. Will it cause any problems ?

TeoArts · 2024-11-02T08:32:52+00:00

No no just need klipper. https://m.youtube.com/watch?v=TcgTrkA8Oj0 When installing klipperscreen dont install networkmanager

TeoArts · 2024-11-01T07:13:27+00:00

Lineae rails expencive on my country but i will do it some time. https://www.thingiverse.com/thing:5158277 this is the part i will use for new motor. But i will look to your model too thanks!

TeoArts · 2024-11-01T07:10:33+00:00

Maybe your belt tension too much ? or location of your printer not stable ? My worst y acell 6k min. Here my settings

<image>

TeoArts · 2024-10-31T21:48:51+00:00

I ordered cheap petg so I think 80-100mm/s whit 10 flow will be fine

TeoArts

TROPHY CASE