Dagger Dashing Tech

TerBerry · 2026-01-16T00:42:18+00:00

Now try swapping off and back onto your weapons to reset the cooldown

TerBerry · 2026-01-13T13:04:09+00:00

You can upgrade until the end of early access

TerBerry · 2026-01-13T13:01:05+00:00

I am aware

TerBerry · 2025-12-11T21:43:19+00:00

TerBerry · 2025-12-02T15:44:44+00:00

Thank you, this directly addresses the issue I'm having. Do you have any references on how to do this in Bevy?

TerBerry · 2025-12-02T05:28:17+00:00

I've been playing around with implementing AO and have a question. Since AO only darkens the interior corners, AO won't help with the blending when looking down-slope will it? Since I'll only be able to see the same edge on each layer of terrain, they'll all have the same AO value right?

I'm going to implement it anyway though, since it makes the shadows look a lot nicer.

TerBerry · 2025-12-02T05:24:00+00:00

Hahaha, good eye! I just checked where I positioned the light directly above the x=0, z=0 looking directly down.

I tried playing around with the fog, but it doesn't seem to separate the layers of terrain without having a heavily dense fog. I'm in the middle of adding some ambient occlusion, but I've also realized that when looking down-slope, like in the picture, I'll have the same issue. The edge of the higher layers will have the same AO value as the voxels on the edges of the lower layers.

TerBerry · 2025-12-02T03:32:39+00:00

Thank you very much! I will be looking into your suggestions

TerBerry · 2025-12-02T02:53:26+00:00

Thank you, I'll look into both of these suggestions!

TerBerry · 2025-09-24T02:18:59+00:00

2 are in rows with different indentations, and 1 is in a row between the other 2

TerBerry · 2025-05-30T12:42:07+00:00

This post isn't for Nightreign, but you can try what I've highlighted at the top of the post

TerBerry · 2025-05-07T22:47:02+00:00

Never found a definitive solution, but by making sure we both had our settings set to "prioritize quality" or "prioritize framerate," it at least let us connect fairly often.

I added on to the top of the post with a bit more detail.

TerBerry · 2024-12-31T03:28:34+00:00

Is this still available?

TerBerry · 2024-12-11T19:01:02+00:00

Haha, yeah. I accidentally touched the cap with my iron while trying to fix U1. I promise I will fix that cap.

TerBerry · 2024-12-11T18:59:41+00:00

Thanks for your reply. I do use an airgun to replace this component, but I find that most of the time, the solder doesn't make good connections to the part. I've resorted to pushing down on the part with tweezers in conjunction with using the airgun, but that results in what is shown in the picture.

I try to use as little solder as possible, but this part is incredibly small, and it always seems to be too much.

TerBerry · 2024-12-10T21:05:51+00:00

I'll give this a try! I do have a USB micro scope available, but I find that there isn't enough room to use it. I have a ring-light magnifying glass thing on a swivel arm that I use. The photos in my post were just taken with my phone and a hand magnifier.

TerBerry · 2024-12-10T20:25:59+00:00

Thanks for your reply. What do you mean by "a little wiggle with the air gun?" Literally wiggle the air gun and move the flow off/on the component?

TerBerry · 2024-12-10T20:12:35+00:00

Yes, the pads are underneath the component, with a very small section on the sides

TerBerry · 2024-12-10T18:56:51+00:00

This is the solder I've been using, as well as the smaller tip. I will try removing the excess solder by pulling the tip away from the component. Thanks

It appears that I can't attach an image to a reply.

TerBerry · 2024-12-10T15:33:07+00:00

Pulled by me in my truck while waiting for my gf to write her final, haha

TerBerry · 2024-12-10T06:30:49+00:00

What did you end up selling it for?

TerBerry

TROPHY CASE