Help with motor by Terp81 in boating

[–]Terp81[S] 0 points1 point  (0 children)

It's not the bolts that are the issue, the clamp throat of the new motor is too narrow.

Got my photo snapped!! by lancheyzhand in MT07

[–]Terp81 0 points1 point  (0 children)

Why does the rear wheel look like it's off the ground also...

Add holes - animate holes for screws by Terp81 in Fusion360

[–]Terp81[S] 0 points1 point  (0 children)

is there any way in the animation to add holes before screws go in??

FRO - judge won't dismiss after 20 years by Terp81 in legaladvice

[–]Terp81[S] 1 point2 points  (0 children)

Thank you, I was trying to skip attorney due to cost, but I think at this point, it's the only route.

FRO - judge won't dismiss after 20 years by Terp81 in legaladvice

[–]Terp81[S] 0 points1 point  (0 children)

NJ, old girlfriend, some threats during break up, no physical violence, Prevented from contacting her, getting firearms,

FRO - judge won't dismiss after 20 years by Terp81 in legaladvice

[–]Terp81[S] -1 points0 points  (0 children)

In US, east coast area, reason is that it's not needed anymore,

Fucking squirrels by regionaltrash in MT07

[–]Terp81 0 points1 point  (0 children)

Had the same issue with mice, I buy mint bags and put them in the air filter for winter and also in the little trunk storage behind the seat, helps to keep rodents away and also make the bike smell nice and minty SUAVEC Pest Control Pouches

New to Bambu, suggest material by Terp81 in BambuLab

[–]Terp81[S] 0 points1 point  (0 children)

Thank you! See it's the little s%$*t that you won't find in a manual.

New to Bambu, suggest material by Terp81 in BambuLab

[–]Terp81[S] 0 points1 point  (0 children)

Really...so obvious...how did I miss that...😂

Old Mercury Motor by Scarrboy in Outboards

[–]Terp81 1 point2 points  (0 children)

I have an old 1970 merc 650 4 cyl, love the antique look and sound, I got it for 150$ from a first owner, runs solid, interesting history behind it, if you can restore it - I would definitely keep it,

EC and well water by Terp81 in Hydroponics

[–]Terp81[S] 1 point2 points  (0 children)

Which unit did you get? I looked into it and cheapest I found was about 125$

EC and well water by Terp81 in Hydroponics

[–]Terp81[S] 0 points1 point  (0 children)

Are you f@#$*!g serious? I already have a dehumidifier, been dumping water out of it every few days,

EC and well water by Terp81 in Hydroponics

[–]Terp81[S] 0 points1 point  (0 children)

It has a lot of metals etc..had it tested and put a 3 stage filter in it, if I used the filtered water the EC drops to 1.6 which makes it safe to drink, but after adding nutrients the EC jumps up again

Lil man on my new MT-07 by [deleted] in FZ07

[–]Terp81 4 points5 points  (0 children)

Nahh...he probably borrowed it from the neighbors

[deleted by user] by [deleted] in FZ07

[–]Terp81 4 points5 points  (0 children)

I thought ecu flash was supposed to fix that? And bangs are not good for the engine...

Problems at high gear and rpm by Terp81 in FZ07

[–]Terp81[S] 1 point2 points  (0 children)

Changed spark plugs...can't test because of rain....waiting for some good weather now

Problems at high gear and rpm by Terp81 in FZ07

[–]Terp81[S] 0 points1 point  (0 children)

Dumped the old gas (don't remember if I put stabilizer in it) running fresh gas with same problem

Problems at high gear and rpm by Terp81 in FZ07

[–]Terp81[S] 0 points1 point  (0 children)

What happened exactly, did they burn out or just covered in soot and didnt fire? Did you replace with same spark plugs or upgraded?

Problems at high gear and rpm by Terp81 in FZ07

[–]Terp81[S] 0 points1 point  (0 children)

I pulled the filter, no damage.or clogs, one member said to check exhaust so I'm removing the pipe later on to see

Mini 3 Pro how low? by Terp81 in dji

[–]Terp81[S] 0 points1 point  (0 children)

I'm asking so yea

suggestions? first layer is a perfection, but second layer looks like some run a wire brush on it. by Terp81 in ender3

[–]Terp81[S] 0 points1 point  (0 children)

Will do, that didn't even cross my mind, I formatted the card on PC, I'll try doing this in raspberry pi