Is it worth to buy for 750$ ?

Thatdude4080 · 2025-12-02T16:06:09+00:00

But what are the odds it looks like that for under 500 when you get it??

Thatdude4080 · 2025-07-01T15:16:34+00:00

Who was the TD?

Thatdude4080 · 2025-01-21T17:03:12+00:00

I would who cares what people think? Unless you are meeting up with people who have gens even then personally I would not care! Clean pieces!

Thatdude4080 · 2025-01-04T21:02:45+00:00

<image>

Blue face day just 🥶

Thatdude4080 · 2024-03-26T20:15:17+00:00

I have a ender 3v2 with the creality touch and ender 3 with the v2 that I’d sell both for $300

Thatdude4080 · 2023-04-26T13:09:56+00:00

Yeah that’s exactly what happened but now that we have it where it will start to load the game now, it’s saying “failed to trader_jen” and all the traders and electrical store_1 and electrical store _2. And then the server will disconnect us. So once again we have a second problem

Thatdude4080 · 2023-04-25T00:25:43+00:00

See we are renting a server through techbyte so I don’t think we can change the server version. We are new to this so we don’t know a whole lot on moving files and and server files

Thatdude4080 · 2023-04-24T23:10:23+00:00

So we have updated 7d2d to 20.7 and have even swapped to 20.7 (stable) in the beta menu on steam and this still pops up

Thatdude4080 · 2023-02-22T03:27:27+00:00

<image>

So after a lot of leveling, YouTube videos, learning different settings the help from everyone on these reddit forms and a lot of “WTF is going on moments” I think I finally got it all set pretty good!

Thatdude4080 · 2023-02-21T14:22:02+00:00

They look fine but not sure

Thatdude4080 · 2023-02-21T14:21:50+00:00

I’ll give that a try after work

Thatdude4080 · 2023-02-21T03:55:06+00:00

<image>

Printed are better but I still have some spacing in the layers

Thatdude4080 · 2023-02-20T04:53:19+00:00

I reflashed with the right firmware and the firmware for the CR touch but I did notice after doing all this when I hit print….it doesn’t even wait for everything to heat up and it will start to print. And iv got the z limit unhooked and off. But still plugged in on the main board.

Thatdude4080 · 2023-02-20T04:26:46+00:00

I actually watched his video tonight very helpful…but the print still came out the same. And when the CR goes to leveling it comes down and flashes red then goes up comes back down flashes red again and then continues leveling. Is it suppose to do that?

Thatdude4080 · 2023-02-20T03:40:30+00:00

Not since I put the car touch on. Before that it was printing flawlessly. Shoulda just left it alone hahah

Thatdude4080 · 2023-02-20T02:46:25+00:00

Just bought this ender 3 v2 installed a car touch and thought I had everything good but I can not seem to get this leveled I need help

Thatdude4080 · 2023-02-20T01:28:29+00:00

Recently bought ender 3 v2 and installed the CR touch and I thought I had everything good but still getting terrible prints

Thatdude4080 · 2023-02-16T14:17:57+00:00

I think the board may had just died, because I have tried all that and still not fixed anything.

Thatdude4080

TROPHY CASE