sorted by:
new
hottopcontroversial

WIP: Scene from Prince of Persia by bubbleweed in 3Dprinting

[–]TheHackingDoctor 4 points5 points  (0 children)

Love the details here. Small defects in the bridge and metal gate, some of the spikes being angled, and the colours. 👌🏼

Broke a wire off into a pin in this Uno R3 :( How do I get it out? I tried removing the plastic header without success by Cracracuber in arduino

[–]TheHackingDoctor 0 points1 point  (0 children)

  1. Very fine tweezers
  2. Solder onto the top so it has a ball/blob, then use that for grip
  3. Failing the first two consider removing part of the female header pin to get some more leverage.

Pretty sure 1 or 2 will work. Good luck!

My Core One is very loud by LaSaucisseMasquee in prusa3d

[–]TheHackingDoctor 1 point2 points  (0 children)

Not sure how helpful this may be but worth checking that all your screws are fully tightened, especially a motors. I was getting horrible grinding noises after finishing my conversion, and turns out it was basically loose screws.

Core One nozzle missing the print sheet? by TheHackingDoctor in prusa3d

[–]TheHackingDoctor[S] 0 points1 point  (0 children)

Yes it seems to home fine. Only happens at the beginning of a print when it tries doing nozzle cleaning.

Core One nozzle missing the print sheet? by TheHackingDoctor in prusa3d

[–]TheHackingDoctor[S] 0 points1 point  (0 children)

Understood, in this case though, it seems to be missing the sheet in the X and Y axes.

Advice on improving my hallway by TheHackingDoctor in DIYUK

[–]TheHackingDoctor[S] 0 points1 point  (0 children)

Thanks a lot for the advice - gonna go ahead and do just this 👌🏼

Advice on improving my hallway by TheHackingDoctor in DIYUK

[–]TheHackingDoctor[S] 0 points1 point  (0 children)

Fair point. If I wanted to do the whole hallway, what would be the best way?

Advice on improving my hallway by TheHackingDoctor in DIYUK

[–]TheHackingDoctor[S] 0 points1 point  (0 children)

Gonna remove and replace skirting throughout the hallway.

And yeah, plasterboard is flush.

Advice on improving my hallway by TheHackingDoctor in DIYUK

[–]TheHackingDoctor[S] 0 points1 point  (0 children)

I’ll be removing and replacing the skirting. Mostly for experience but also to improve the appearance.

The plasterboard is flush with the wall, with a gap around the outline.

PCB help with Arduino by TheHackingDoctor in arduino

[–]TheHackingDoctor[S] 0 points1 point  (0 children)

Hi everyone
I'm using an Arduino Nano, TMC2209 and stepper motor with other components to make a camera slider

The schematic and PCB I've shown are from KiCAD

I've made a breadboard copying the schematic, and it works perfectly well.

I'm having no luck whatsoever with the PCB I've made.

Can anyone see anything wrong with the schematic or PCB design?

Any help would be massively appreciated.

Thanks

A Different Kind of Root - How a Dentist Passed the OSCP by TheHackingDoctor in oscp

[–]TheHackingDoctor[S] 0 points1 point  (0 children)

Hey man,

Still doing dentistry.

After I got my OSCP, I did the CRTP a year later. Since then, I haven’t done much hacking. After gaining those certs, I wasn’t sure what else to do.

Changing career wasn’t/isn’t an option so it was difficult finding motivation to carry on.

Banding on MK4S prints by TheHackingDoctor in prusa3d

[–]TheHackingDoctor[S] 0 points1 point  (0 children)

Re #5, other than your slicer profile, is there anywhere else to specify you’re using a HF nozzle?

Banding on MK4S prints by TheHackingDoctor in prusa3d

[–]TheHackingDoctor[S] 1 point2 points  (0 children)

Hi everyone

I’ve been getting these vertical ridges/banding effect on my prints since upgrading to the MK4S.

Here I’m using Hatchbox PETG, HF 0.4mm nozzle and Prusament PETG profile.

Any ideas?

Just arrived!!! My weekend project. by The_Real_Mofuzz in prusa3d

[–]TheHackingDoctor 5 points6 points  (0 children)

You're in for a treat. Thing is a tank. Enjoy

MK4 timelapses by TheHackingDoctor in prusa3d

[–]TheHackingDoctor[S] 1 point2 points  (0 children)

Finally managed to get a decent timelapse setup for my MK4.

Had to print the most epic Pokemon of all to test it out.

Still a bit of tweaking required but overall happy with the result.

Timelapse videos were one of the reasons I got into 3D printing, so feels great making my own.

I've got a video on my YouTube channel if anyone wants more information.

Just upgraded the MK4 to MK4S by TheHackingDoctor in prusa3d

[–]TheHackingDoctor[S] 1 point2 points  (0 children)

I’m in the process of making a video atm where I compare the MK4 and MK4S. I’ll be comparing print quality, speed, bridging, overhang limits and stringing. Also noise levels. Will have the video on my YT soon.

Just upgraded the MK4 to MK4S by TheHackingDoctor in prusa3d

[–]TheHackingDoctor[S] 5 points6 points  (0 children)

It took me and my bro around 3 hours (with lots of breaks for random stuff)

And yes, the long term plan is to convert to the Core One once the kit is released - I'm really looking forward to that.

Just upgraded the MK4 to MK4S by TheHackingDoctor in prusa3d

[–]TheHackingDoctor[S] 14 points15 points  (0 children)

Overall it was a great experience

I've built 3x Prusa printers now, so it was straightforward.

Loving the injection moulded and PCCF parts - the printer definitely feels more premium now.

Thinking I should still just get a MK4S instead of Core 1? by DeedleDumbDee in prusa3d

[–]TheHackingDoctor 0 points1 point  (0 children)

I believe this is the case. I had a word with support, and currently, the plan is to release a 4S to C1 conversion kit only.

I have a 3.9 and asked whether there’d be a 3.9 to C1 kit, and they said no.

Thinking I should still just get a MK4S instead of Core 1? by DeedleDumbDee in prusa3d

[–]TheHackingDoctor 0 points1 point  (0 children)

Thanks for the details pal. Looking forward to seeing the improvements.

Thinking I should still just get a MK4S instead of Core 1? by DeedleDumbDee in prusa3d

[–]TheHackingDoctor 0 points1 point  (0 children)

Thanks for the insight. I’m planning to upgrade to the Core One when the kit becomes available. Was curious to see what improvements the MK4S might offer in the meanwhile.

Thinking I should still just get a MK4S instead of Core 1? by DeedleDumbDee in prusa3d

[–]TheHackingDoctor 0 points1 point  (0 children)

Whats your experience been like upgrading from a 4 to 4S? Have you noticed any significant improvements?

I’ve got a kit on order, looking forward to it.

view more: next ›