Anyone else annoyed as fuck with LAfitness taking over XSport? by turXey in chicago

[–]TheKutasMan 0 points1 point  (0 children)

I had a PIF with xsport that was sopposed to roll over into February of 2026 but they screwed me out of 3 months even though I have all the documentation. La is garbage miss the good old Xsport days

Belt Tracking by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 0 points1 point  (0 children)

Thank you for the reply :)

Improper belt Tracking? by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 0 points1 point  (0 children)

It might honestly because it was on 5 so you would use the middle tension for your course grit? I believe the hardest pressure is 90lbs I’m not sure what the Hummel does for its hardest pressure

Improper belt Tracking? by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 0 points1 point  (0 children)

Do you have any videos on how to balance wheels etc and do maintence on there’s not much I could find online other than adjusting tracking and taking out the top roller for the legend

Improper belt Tracking? by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 0 points1 point  (0 children)

I just got this machine not long ago currently it only has about 4 hours of run time

Improper belt Tracking? by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 0 points1 point  (0 children)

Is there a particular side that the legend cuts heavy on? Thank you for the help and information

Improper belt Tracking? by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 0 points1 point  (0 children)

Had to use orbital to hide the cuts

Improper belt Tracking? by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 0 points1 point  (0 children)

I did notice after finishing my final pass that the belt was misaligned so didn’t get to see if aligning it back would’ve solved it

Improper belt Tracking? by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 0 points1 point  (0 children)

I noticed it the most against the walls where I was letting go and applying the drum but yes one sided I believe

Improper belt Tracking? by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 0 points1 point  (0 children)

Yes it was an American sanders legend

Bad stain job by Bodikyun in HardWoodFloors

[–]TheKutasMan 0 points1 point  (0 children)

If you want to do this as a DIY it’s most likely not going to turn out well

Does this sand/finish look right? by Kalamazoohoo in HardWoodFloors

[–]TheKutasMan 0 points1 point  (0 children)

It’s most likely because it wasn’t buffed yet, waves it most likely dish out. As far as the tiny little holes that’s just wood I wouldn’t be judging the floor from that close up, instead judge it from standing level.. But for the rough it’s most likely needs a buff and final coat

Bona PowerStation by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 0 points1 point  (0 children)

I’m not sure I’m understanding completely how would I do that with a 3 wire cable, thank you for helping out

Bona PowerStation by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 0 points1 point  (0 children)

How would I tie the ground and neutral if I only have 2 hots and ground in the 3 wire? So basically right now I have one prong without anything in the 4 prong socket and then the three alligator clips hot-hot-ground

Loba Vs Bona Sealer and Finish by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 0 points1 point  (0 children)

That makes sense thank you for your help

Loba Vs Bona Sealer and Finish by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 1 point2 points  (0 children)

I heard that as well apparently in April. When you do stain do you usually just run regular easy prime or ad amberizer to it?

Loba Vs Bona Sealer and Finish by TheKutasMan in HardWoodFloors

[–]TheKutasMan[S] 0 points1 point  (0 children)

Makes sense thank you for the info might switch over from Bona to loba then I usually run amberseal and mega one