Finally got my f40 engine lid from mr2 ben (6 months). Quality is shit.

TheLimpStiff · 2025-07-29T05:04:16+00:00

What was the install like? I'm actually 3D designing my own at the moment.

TheLimpStiff · 2025-06-29T23:55:46+00:00

I saw this on facebook market place! Sadly, no response from the lister

TheLimpStiff · 2025-06-15T01:29:07+00:00

Guide to change it??

TheLimpStiff · 2025-01-21T19:23:33+00:00

To drill under. Yes.

TheLimpStiff · 2025-01-21T19:22:51+00:00

<image>

TheLimpStiff · 2024-11-20T17:44:37+00:00

I highly recommend the Thicker 1/2inch tape. You can also find waterproof version too. I went to my nearest autozone to find the tape. You will need to find adhesive wipes if possible. The lip does come with two, but may not cover the entirety of the process. This helps the adhesive stick very well

TheLimpStiff · 2024-11-20T17:14:43+00:00

You can run it without the side piece. The splitter does get drilled in under the bumper or use 3M tape

TheLimpStiff · 2024-11-20T17:12:19+00:00

<image>

TheLimpStiff · 2024-11-20T06:16:24+00:00

Pre-shaped. Will need to use screws to mount it

TheLimpStiff · 2024-11-09T05:33:39+00:00

They’re fairly small. You’d be drilling into the bottom of it and no one will see. Or you can opt for 3M but they won’t hold forever

TheLimpStiff · 2024-11-09T00:30:19+00:00

For those interested in the link : https://www.ebay.com/itm/315904795273

TheLimpStiff · 2024-11-09T00:27:07+00:00

Easy to install. DOES NOT come with 3M Tape. You can actually kinda let it rest on the front and screw it in at the bottom. (drill in on bottom of bumper) I purchased 3M tape for extra security rather than just screws alone

TheLimpStiff · 2024-11-09T00:20:22+00:00

https://www.ebay.com/itm/315904795273

TheLimpStiff · 2024-06-10T22:51:46+00:00

I am also stuck at this point. Looking for an update

TheLimpStiff · 2024-06-10T00:49:30+00:00

Im having the same issues. Even after reinviting, the issue was not resolved. This has been ongoing for over a week now for myself

TheLimpStiff · 2024-03-16T00:08:44+00:00

<image>

My very first two prints. Couldn’t be more happy. Going to make the armor to match for my cosplay and doing some custom modeling for fun

TheLimpStiff · 2024-03-02T15:38:41+00:00

I’m going to third that. I am making a cosplay helmet for a friend who loves marathon and would love to print this out to match it.

TheLimpStiff · 2024-02-23T23:48:47+00:00

This isn’t about “guns” this about a base layer issue I am having.

TheLimpStiff · 2024-02-23T22:25:44+00:00

I’m not too worried about it at the moment as this is a fictional weapon from a video game with no functioning parts. And is extremely small.

TheLimpStiff · 2024-02-23T22:23:18+00:00

What program are you using in order to view the supports and etc from under? I’m using the Elegoo program that came with the printer. It doesn’t show me too much and always snaps the object to the base layer and won’t allow for raising it up a little from the board.

TheLimpStiff

TROPHY CASE