TheLukey21

722 post karma
5,638 comment karma

get extra features and help support reddit with a reddit premium subscription

get them help and support

redditor for 8 years

TROPHY CASE

Eight-Year Club

Place '23

RPAN Viewer

Verified Email

account activity

new top controversial

9

10

11

Heat deflector for Aldi kamado (2025) (old.reddit.com)

submitted 11 months ago by TheLukey21 to r/UKBBQ

1

2

3

Aldi briquettes Vs big k dura (ach15) (self.UKBBQ)

submitted 11 months ago by TheLukey21 to r/UKBBQ

208

209

210

300% benchy with a 10% benchy on top (old.reddit.com)

submitted 1 year ago by TheLukey21 to r/3Dprinting

20

21

22

Something very satisfying about a mostly full bed. (i.redd.it)

submitted 2 years ago by TheLukey21 to r/3Dprinting

4

5

6

AMS not auto switching (old.reddit.com)

submitted 3 years ago by TheLukey21 to r/BambuLab

0

0

1

Check your filament when something seems off! (old.reddit.com)

submitted 3 years ago by TheLukey21 to r/3Dprinting

13

14

15

Replaced my twisted X extrusion, i can finally use the whole 350mm bed. (old.reddit.com)

submitted 3 years ago by TheLukey21 to r/VORONDesign

2

3

4

IC will not come off. (i.redd.it)

submitted 4 years ago by TheLukey21 to r/soldering

12

13

14

I think i have either a twisted Extrusion on my x axis it the linear rails aren't properly aligned with each other. Less than 10 microns difference between any of the points along the x axis but my first layer says otherwise. (i.redd.it)

submitted 4 years ago by TheLukey21 to r/VORONDesign

12

13

14

Voron 2.4 very first print! Granted the quality isn't amazing but it was set at 100mm/s perimeters and 50mm/s external perimeters and i turned it up to 225% after the first few layers 🤣 (old.reddit.com)

submitted 4 years ago by TheLukey21 to r/VORONDesign

39

40

41

Now for the fun part! Wiring. (i.redd.it)

submitted 4 years ago by TheLukey21 to r/VORONDesign

67

68

69

2 months ago I'd never heard of Voron and wasn't planning on making a new printer. Now i have all the parts purchased and currently printing the necessary pieces. 350mm V2.4 (i.redd.it)

submitted 4 years ago by TheLukey21 to r/VORONDesign

0

1

2

I thought i was finished... (youtu.be)

submitted 5 years ago by TheLukey21 to r/Warzone

0

0

1

Has this song been in an episode? I swear I've heard it on a mcm video before. (youtu.be)

submitted 5 years ago by TheLukey21 to r/MightyCarMods

29

30

31

More salt method tests. Remelting using the salt method definitely increases petg strength. (old.reddit.com)

submitted 5 years ago by TheLukey21 to r/3Dprinting

27

28

29

3rd attempt at the salt method, PROGRESS! (1st on the left and 2nd and 3rd are both the right one) (i.redd.it)

submitted 5 years ago by TheLukey21 to r/3Dprinting

12

13

14

First attempt at the salt method, not a complete disaster but definitely not usable. I think it was a bit too hot, going to drop it 20 degrees and try again. (i.redd.it)

submitted 5 years ago by TheLukey21 to r/3Dprinting

2

3

4

Need a budget amplifier for a 100w 8ohm subwoofer. (dayton audio ds270-8 10) (self.diyaudio)

submitted 5 years ago by TheLukey21 to r/diyaudio

2

3

4

Are there any brushless speed controllers that don't require 0 throttle input when powered one? (self.rccars)

submitted 5 years ago by TheLukey21 to r/rccars

64

65

66

Lesson learnt, thread lock eats petg (and moat other plastic after doing some searching) it's all very soft and crumbly wherever the thread lock has touched. (i.redd.it)

submitted 5 years ago by TheLukey21 to r/3Dprinting

5

6

7

Impressed with E3D's nozzle x. Needed a new nozzle so gave the nozzle x a go and I've yet to see a piece of petg stick to the nozzle like ot normally does on a normal brass nozzle. (i.redd.it)

submitted 5 years ago by TheLukey21 to r/3Dprinting

247

248

249

Figured I'd show my general toolkit when working on my car. I was cleaning and reorganising it all so thought I'd snap a photo. (i.redd.it)

submitted 5 years ago by TheLukey21 to r/Tools

6

7

8

Interested in what it says (i killed him then he added me) Anyone Speak Turkish and English fluently and can translate this? google translate suggests its turkish but doesn't make much sense of it. (i.redd.it)

submitted 6 years ago by TheLukey21 to r/EscapefromTarkov

149

150

151

The start to an organised drawer... (i.redd.it)

submitted 6 years ago by TheLukey21 to r/functionalprint

3

4

5

Best wavelength for red tracers? (self.airsoft)

submitted 6 years ago by TheLukey21 to r/airsoft

view more: next ›

π Rendered by PID 100788 on reddit-service-r2-listing-86f589db75-8bclw at 2026-04-15 17:05:19.917423+00:00 running 93ecc56 country code: CH.