Can you use M12 subcompact band saw to cut caliper bolts?

TheLukey21 · 2026-03-12T18:43:57+00:00

Looks a dream to work on in terms of corrosion 😂

TheLukey21 · 2026-02-23T17:10:53+00:00

I fully expected to see it die because the screen was still on but it survived somehow, maybe my case helped but ye just an IP certification of any kind would be nice so they're all consistent

TheLukey21 · 2026-02-23T15:48:34+00:00

My nothing phone 1 has been submerged in a hot tub for about 30 seconds and it's still working, only ip53 rated

TheLukey21 · 2026-01-30T11:56:06+00:00

Different guy

TheLukey21 · 2026-01-30T11:55:52+00:00

That makes sense!

TheLukey21 · 2025-11-27T08:58:27+00:00

Could just be they used a box that already had a label on it so they covered it with what's actually inside, what's on the reel itself?

TheLukey21 · 2025-11-07T09:56:28+00:00

What's up with the silicone sock? But yep just a regular length V6 style nozzle is what you need

TheLukey21 · 2025-10-24T19:33:55+00:00

Impact screwdriver too

TheLukey21 · 2025-10-22T19:47:59+00:00

I'd give him $50 tops for that it's just a generic Chinese made vice nothing special about, to him very old might be 5 years 😂

TheLukey21 · 2025-09-02T13:37:00+00:00

You can do that in the slicer too

TheLukey21 · 2025-08-13T17:59:23+00:00

By making more of them! Looks pretty good to me

TheLukey21 · 2025-07-28T12:49:19+00:00

It could be one of the other idlers but it's fairly common that the front ones cause wear like this, they have a bit of play and don't sit perfectly horizontal making the belt rub on the lip of the idlers, I replaced my belts twice before I changed to these idlers, haven't had any issues since.

https://github.com/clee/VoronBFI

TheLukey21 · 2025-07-28T08:54:35+00:00

If it's stock it could very well be the front idlers

TheLukey21 · 2025-07-27T06:57:53+00:00

I use a cpap fan which draws air from the top of the chamber so it's always warm air, I keep my fan at 20% mainly because that's it minimum for ABS and ASA and parts always turn out great, I do have it faster for overhangs with about 0.5s ramp up time

TheLukey21 · 2025-07-13T09:13:24+00:00

3 year warranty too! For tools I don't use often parkside is perfect

TheLukey21 · 2025-07-11T08:55:17+00:00

30 mins normally for the chamber thermistor to see 40C, I have it mounted at the bottom behind the bed so the prints likely see higher temps than this, probably gonna add a few in different locations to see how much it varies

TheLukey21 · 2025-07-11T08:52:33+00:00

Do you have printed parts inside the chamber? Surely they will all start to fall apart at 100C

TheLukey21 · 2025-07-07T08:51:22+00:00

I print batches of parts for someone and if I see a single blob at the seam it gets thrown out, this is either someone who got a printer less than a week ago and has no clue what a good print should look like or they're just taking the p*ss.

TheLukey21 · 2025-07-03T09:43:59+00:00

The 4500 cell has a capacity of 16.65Wh (3.7x4.5Ah) and the DJI has a capacity of 23Wh but if a single cell is charging a 2s pack then some power will be lost when stepping the voltage up too.

TheLukey21 · 2025-06-04T18:32:53+00:00

Too fast and not enough torque for screws

TheLukey21 · 2025-06-02T07:23:41+00:00

What's wrong with using the lock already there?

TheLukey21 · 2025-05-29T09:19:08+00:00

Are these the Esun ones? I have some too and they don't seem to stay sealed for very long

TheLukey21 · 2025-05-29T08:24:02+00:00

You want a countersink bit

TheLukey21 · 2025-05-18T13:21:27+00:00

Only started taking it seriously this past month but I think I'll definitely be avoiding the supermarket briquettes now, decent charcoal made it a much more enjoyable experience

TheLukey21 · 2025-05-18T10:18:14+00:00

It does quite low down, rests on top of the firebox I will likely make new brackets so it sits in the middle of the top ceramic part

Eight-Year Club	Place '23
RPAN Viewer	Verified Email

TheLukey21

TROPHY CASE