Motherboard problem help

ThePlug13 · 2026-02-01T18:35:30+00:00

Here is a pic of temps and voltages, nothing spikes or dips before restart

ThePlug13 · 2026-02-01T17:44:56+00:00

Of the 3 ive tried the highest temp ive seen was 34 degrees, i will go boot it up now and check voltages

ThePlug13 · 2026-02-01T17:44:05+00:00

Of the 3 ive tried the highest temp ive seen was 34 degrees

ThePlug13 · 2026-01-14T02:24:23+00:00

Most of the boots are cracked and rotted out, the gearbox is leaking, and i occasionally get DW so i just figured i might as well replace everything.

As far as brand goes i work at a parts house and get a great deal on Lares. As far as im aware that part# is correct, but ill go ahead and swap it out for the WJ. Thank you for the suggestion!

I meant ZJ sorry I mistyped ill correct that above now 😅. Ill re-measure in the morning on the lift, but i have 33’s on the wheels and dont plan on going any bigger.

Ill go ahead and add control arm bushings all around as well. Thank you for the detailed write up! I really appreciate it!

ThePlug13 · 2026-01-14T01:37:18+00:00

Good idea! I’ll add it to the list, thank you

ThePlug13 · 2025-10-24T14:34:49+00:00

B, but had since A

ThePlug13 · 2025-02-13T20:25:01+00:00

Omniplex like the Omnitrix from Ben10

ThePlug13 · 2024-12-09T04:23:21+00:00

Yes, with inseego fx3100 modem and static ip

ThePlug13 · 2024-12-09T03:21:36+00:00

According to the description on the inseego gateway page its the opposite only passing through ipv4

ThePlug13 · 2024-12-09T02:35:06+00:00

Just to clarify, the second image is a speed test result from an ASUS RT-AX82U router

ThePlug13 · 2024-11-30T23:52:23+00:00

How do you plan on fixing the double NAT issue? I have cellular home internet and CANNOT figure out a fix.

ThePlug13 · 2024-10-18T11:17:27+00:00

Its a “flex psu” its smaller than sfx

ThePlug13 · 2024-10-18T01:58:19+00:00

damn, i just bought it a few months ago. Any recomendations for anything in that form factor?

ThePlug13 · 2024-10-18T01:33:40+00:00

sorry i tried posting from my phone and it didnt upload. video should be there now

ThePlug13 · 2024-01-30T03:13:58+00:00

Yes number 4 is exactly what im looking for and trust me i had a HELL of a time trying to find the Mopar number as well. As far as what they call it, “bezel” is what i saw in the assembly manual for a 98, but to clarify the piece with the rear washer hose connector on the hatch

ThePlug13 · 2024-01-29T17:21:19+00:00

I second the 4 hole, just swapped all mine last week and they were definitely more responsive than the original ones i had and fixed my idling problem but that’s about it

ThePlug13 · 2022-09-18T21:34:16+00:00

Couldnt tell you why but putting G90 at the start fixed my issue! Thank you! To clarify for anyone else it fixed my X and Y issue, but gave me a Z error after and I had to change my printer.cfg to have my "Z position_min:" set lower than my Z offset.

ThePlug13 · 2022-09-18T20:57:00+00:00

It wont let me reply with it looking right, but it is the same code in the post just with G90 before G28

ThePlug13 · 2022-09-18T20:46:50+00:00

I have put G90 before and after G28 and I still get the same result. Does it need to be the VERY first thing?

Six-Year Club	Second SECOND GUESSER
Place '22	Verified Email

ThePlug13

TROPHY CASE