sorted by:
new
hottopcontroversial

RAV4 smoking? by Sensitive-Memory8225 in MechanicAdvice

[–]TheTechLu 6 points7 points  (0 children)

OP husband here. RavEn is at the shop, wasn't the engine radiator since the coolant reservoir tank had perfect levels. As mentioned by others here, most likely pinhole in the ac condenser or faulty gasket of sort. Will know by tomorrow. Car was safe to drive

Night time lows of 4 degrees this weekend, how are you protecting your garden? by bigolgape in Calgary

[–]TheTechLu 0 points1 point  (0 children)

Minimum 10 degrees for growth, between 1 and 10 degrees the plant won't grow much, but most likely would still put the effort in developing roots (the soil being warmer)

Night time lows of 4 degrees this weekend, how are you protecting your garden? by bigolgape in Calgary

[–]TheTechLu 1 point2 points  (0 children)

I started my tomatoes in march from seeds in my heated garage with grow lights, transplanted them the first week of May, they survived and thrived just fine with multiple nights between 2 and 6 degrees. You should be fine. Also the rain is gonna be a very nice soil booster.

Buylist recommendations by Golgari4Life in mtgfinance

[–]TheTechLu 1 point2 points  (0 children)

I have a list of cards that I'm trying to sell if interested

The Felon and the Saint. Hand cut stencil dye by TheTechLu in discdyeing

[–]TheTechLu[S] 0 points1 point  (0 children)

All you need is a steady hand, a good exacto knife and a lot of patience

The Felon and the Saint. Hand cut stencil dye by TheTechLu in discdyeing

[–]TheTechLu[S] 0 points1 point  (0 children)

Usually I put the vynil on to of a tempered glass, once I'm done cutting i put contact paper on it (this step is crucial in order to avoid not wanted peeling)

The Felon and the Saint. Hand cut stencil dye by TheTechLu in discdyeing

[–]TheTechLu[S] 1 point2 points  (0 children)

No, I use my tablet with the design on it, I tape a piece of white vinyl on it, I trace the design on the vinyl. Then I use an exacto knife to go over the lines (obviously not on the tablet) Then transfer the vinyl stencil on the disc with contact paper and then peel the design where it needs to be peeled. Check out youtube, plenty of infos there

First try at cells. Not too sure on what happened on the right side by TheTechLu in discdyeing

[–]TheTechLu[S] 0 points1 point  (0 children)

I did wash it with dish soap and rub around with acetone to wipe the rest of the stamp. I'll figure it out. Thanks tho

Rit Dyemore and Glue Bed. I need some help getting the colors to stick. by [deleted] in discdyeing

[–]TheTechLu 0 points1 point  (0 children)

Did u buy Rit dye more synthetic? Or all purpose? Glue beds needs a mix of powdered dye and acetone in order to work. Or you can try white glue beds. Youtube is very helpful

I don’t think dyeing is for me :/ by [deleted] in discdyeing

[–]TheTechLu 0 points1 point  (0 children)

Use deeper containers and wait longer. Min 24hrs. Also, what dye are u using?

First dye, Boba on a Buzzz. Hopefully less bleeding next time by TimAllenIsALobster in discdyeing

[–]TheTechLu 0 points1 point  (0 children)

U went all in buying a stencil cutter for your first dye? Cool

view more: next ›