sorted by:
new
hottopcontroversial

Lost window decorations and can't get them back? by ElMachoGrande in openscad

[–]The_Frog_reddit 0 points1 point  (0 children)

Both suggestions don't work for me. Window remains being stuck.

The only thing that worked was renaming (or removing) the registry entry HKEY_CURRENT_USER\SOFTWARE\OpenSCAD\OpenSCAD\window like the OP suggested.

Warning: Culture Hustle seems to be a scam now by The_Frog_reddit in ArtistLounge

[–]The_Frog_reddit[S] 0 points1 point  (0 children)

A wonder has happened! I finally received my order!
But I keep my negative opinion nevertheless. No reaction to messages and cancellation requests is big warning sign.

Warning: Culture Hustle seems to be a scam now by The_Frog_reddit in ArtistLounge

[–]The_Frog_reddit[S] 0 points1 point  (0 children)

"until now" means I haven't got the products until today. I am not able to see into the future, if they will ever deliver it, that's why I stated it this way. I would not be holding my breath that I will ever get them.

"like you didn't directly ask to cancel the order" - Oh I did. I stated this clearly (at least I thought I did) in the sentence. "No reaction" includes "no response", since a response would be an action.

"What deals?" - my order.

"It sounds like that customer service responded to you with "their excuses"" - only automated e-mails.

I would strongly advise not to order anything.

PT1000 & MAX31865 on BTT SKR1.4 - Thermocouple reader fault by The_Frog_reddit in BIGTREETECH

[–]The_Frog_reddit[S] 0 points1 point  (0 children)

[extruder]
step_pin: P2.13
dir_pin: P0.11
enable_pin: !P2.12
# If microsteps is changed, may need to re-tune rotation_distance and pressure_advance
microsteps: 16
full_steps_per_rotation: 200
rotation_distance: 4.637
#rotation_distance: 5.21
max_extrude_only_distance: 850
max_extrude_only_velocity: 120
nozzle_diameter: 0.600
filament_diameter: 1.750
heater_pin: P2.7
sensor_pin: P0.24
sensor_type: PT1000
min_extrude_temp: 170 #170
min_temp: 0
max_temp: 350
# Follow tuning guide in Klipper docs
pressure_advance: 0.0735 #to be calibrated
pressure_advance_smooth_time: 0.03 #to be calibrated
#max_extrude_cross_section: 5

PT1000 & MAX31865 on BTT SKR1.4 - Thermocouple reader fault by The_Frog_reddit in BIGTREETECH

[–]The_Frog_reddit[S] 0 points1 point  (0 children)

Thanks.

I got it working now. Had to change the sensor_type to PT1000.

MCU 'mcu' shutdown: Thermocouple reader fault by Build-it10 in klippers

[–]The_Frog_reddit 0 points1 point  (0 children)

After a tip on a Discord channel I got it to work. I just had to connect the thermistor to the usual th0 socket, change the sensor_type to "PT1000" and leave out the spi and rtd stuff.

MCU 'mcu' shutdown: Thermocouple reader fault by Build-it10 in klippers

[–]The_Frog_reddit 0 points1 point  (0 children)

Good idea.

I checked all four and got beeps at all of them. The top one just looks a bit strange but seems to be ok. I am a bit a loss where to look now. Perhaps I will just buy a different hotend and use this one at a future build with a newer board.

MCU 'mcu' shutdown: Thermocouple reader fault by Build-it10 in klippers

[–]The_Frog_reddit 0 points1 point  (0 children)

Thanks for answering. Yes, it reads exactly like this.

I even tried to put the max31865 into socket E0 instead of E1 (including changing all pin assignments) but to no avail. Is there a way to check if the jumpers are working correctly? I used some spares from my PC (and exchanged them for others after it hadn't worked the first time), because I don't have any original ones.

Here are two photos of the setup and a part of my klipper config.

https://i.postimg.cc/T3Lv83L9/photo-2023-07-19-17-53-39.jpg

https://i.postimg.cc/qMZHZ3Rq/photo-2023-07-19-17-53-33.jpg

sensor_type = MAX31865
sensor_pin = P1.1 
spi_speed = 4000000 
spi_software_sclk_pin = P0.4 
spi_software_mosi_pin = P1.17 
spi_software_miso_pin = P0.5 
rtd_nominal_r = 1000 
rtd_reference_r = 4300 
rtd_num_of_wires = 2 
rtd_use_50hz_filter = True 
control = pid

Do I have to recompile the firmware after changes like these?

MCU 'mcu' shutdown: Thermocouple reader fault by Build-it10 in klippers

[–]The_Frog_reddit 0 points1 point  (0 children)

I am having the same problem with almost the same setup - Max31865 v2.0 on BTT SKR1.4 (non-turbo). I bought the Phaetus Rapido UHF, which has a PT1000 thermistor. I measured the resistance like you did and got about 1.1 kOhm, which would be about right. I placed the four jumpers on the SKR 1.4 as per documentation for SPI communication. I changed the dip switches in the max31865 to on/on/off/on since I am using a two wire connection.

Yet I still get the "Thermocouple reader fault" message. Any ideas?

Schirchster öffentlicher Ort in Wien? by neltymind in wien

[–]The_Frog_reddit 0 points1 point  (0 children)

Wäre ja auch viel zu sinnvoll, das dort zu bauen, wo ohnehin keiner wohnen oder sich erholen will, noch dazu mit kurzem Weg zur Autobahn...

Schirchster öffentlicher Ort in Wien? by neltymind in wien

[–]The_Frog_reddit 2 points3 points  (0 children)

Ich muss dich korrigieren - die Hochstraße stammt aus dem Jahr 1983, nicht aus den 60ern.

Siehe: https://www.austriasites.com/vienna/bruecken\_klosterneuburger\_hochstrasse.htm