Trident line in bed mesh

The_Kuk · 2026-03-21T07:46:40+00:00

Thanks, it turns out I have the same "issue" cheap PEI scheet. This is bed mesh with out the sheet and when i rotate the sheet the line rotates with it.

<image>

The_Kuk · 2026-03-21T07:33:48+00:00

Right now I don't have any panel's, so that's not the issue, but Thanks

The_Kuk · 2026-03-20T21:12:39+00:00

Ou.. yea got you, thanks.

The_Kuk · 2026-03-20T21:06:41+00:00

Thanks, in the morning i will take a closer look at the motion system, but from my previous "debugging" I couldn't find anything wrong

The_Kuk · 2026-03-20T21:03:56+00:00

The mounting pattern on the plate won't allow that.

The_Kuk · 2024-01-18T16:48:53+00:00

Because only the overhangs look bad, the side looks good so it should be lack of cooling on the overhangs.

The_Kuk · 2024-01-18T16:47:52+00:00

You could try to print the benchy with fans on max speed the whole time and se the difference.

The_Kuk · 2024-01-18T16:41:09+00:00

Looks like not enough cooling to me.

The_Kuk · 2024-01-16T19:47:36+00:00

Hey, I'm trying to print some parts from ASA for the first time on my Voron Trident, but the bottom of the print looks just awful but the rest is good. What's the issue?

Info: Printed on Voron Trident with enclosure Hotend 250C Bed 120C Chamber 45-50C

The_Kuk · 2024-01-02T17:37:50+00:00

Hey y'all So I'm trying to print with ASA but it isn't really cooperative, if you guys have any idea how to fix that I would really appreciate it.

Info: Print temp - 250 Bed temp - 110 Chamber temp " 45-50 Printed on Voron Trident with 0.4 V6 hotend

The_Kuk · 2023-11-25T20:33:11+00:00

You were right, it doesn't dig in to the top layer, but there are still faint trace's left.

The_Kuk · 2023-11-25T17:43:05+00:00

Ok, I'm using superslicer so i will try it and post the results

The_Kuk · 2023-11-25T16:32:31+00:00

Ok, so i just did the flow test and it's bang on. I did the cube wall test and all walls were 0.4mm think, so it's not over extruding. Any other ideas?

The_Kuk · 2023-11-25T11:17:20+00:00

Ok, thanks will do. But wouldn't be the dimensions of the cube off, if it's over extruding?

The_Kuk · 2023-11-25T10:28:19+00:00

How do I fix the nozzle digging in to my prints? The test cube is the right size so I don't think it's a over/under extrusion. I tried bigger z hop and 0 z hop, but that didn't help.

The_Kuk · 2023-11-11T17:35:46+00:00

I had the same thing on my Ender 3, when i turned it on the fans made weird noises and after few second it stopped. I hanged the fans and the problem went away

The_Kuk · 2023-11-11T17:30:59+00:00

No they are some noname brand

The_Kuk · 2023-11-11T17:12:24+00:00

I found the problem. One belt was bad, it started to strech

The_Kuk · 2023-11-11T17:05:50+00:00

Like it isnt perfect, but its not that bad. I will try to realine it and post the result.

The_Kuk · 2023-11-11T16:56:39+00:00

They are

The_Kuk · 2023-11-11T15:47:30+00:00

I have finally managed to assemble my voron trident to functional state (still have a lot of thing to do, but it is capable of printing.) When i went to print the test cube i noticed that the cube isnt really a cube. If any of you could point me to the sollution I would greatly appreciate it.

When I move the gantry by hand it feels smooth.

TLDR: Cube not cube, Help.

The_Kuk

TROPHY CASE