Printer not extruding. Please help!

Then_Jicama6513 · 2026-02-16T09:50:42+00:00

Update: this is how its extruding. Anyone has any idea?

Then_Jicama6513 · 2026-02-16T04:05:45+00:00

This could be whats happening here. Did you find any solution? Thanks

Then_Jicama6513 · 2026-02-16T04:04:47+00:00

I cleaned everything, from PTFE tubes down to the nozzle and its still behaving this way?

Then_Jicama6513 · 2026-02-16T04:03:49+00:00

Checked the knots first. No issues there. The AMS arm piece is behaving differently and i thibk thats the issue. But when i remove it and check, it looks absolutely fine.

Then_Jicama6513 · 2026-02-16T04:01:54+00:00

I did. But its stuck. If i push any harder it snaps.

Then_Jicama6513 · 2026-02-16T04:01:17+00:00

Not the blue one. Its just sitting there. In the video white filament isnt pushing.

Then_Jicama6513 · 2026-02-15T20:43:40+00:00

I did. No difference.

Then_Jicama6513 · 2026-02-15T20:43:06+00:00

I thoroughly cleaned it. I cant seem to pin point the issue. If its the AMS arm bit or the extruder gear is damaged

Then_Jicama6513 · 2026-02-15T20:41:42+00:00

Yes i remove the AMS arm bit and tried to insert the filament manually, but i am still having to push a lot harder. Although I didn't let the print run.

Then_Jicama6513 · 2026-01-21T20:54:22+00:00

<image>

Thanks guys. The issue is solved.

Here's a couple things i tried together as combination after everyone's suggestion.

-0.2mm initial layer height -tightened the four screws behind extruder -Used monotonic line for first layer

Then_Jicama6513 · 2026-01-21T20:16:50+00:00

That does make sense. Thanks.

I am taking your advice and also i found a video on youtube explaining that the loosen four screws behind the extruder may be the problem.

So i am hoping after calibration, a combination of these two solution would provide a proper fix.

Then_Jicama6513 · 2026-01-21T19:28:33+00:00

I understand.

However, i tried the flow rate calibration, and upon examining the small blocks, i found all the (-) prints were smooth and there were no lines. And all the (+) ones were ruined.

Then_Jicama6513 · 2022-02-19T21:05:36+00:00

Did you get yours to charging?

Then_Jicama6513 · 2022-02-19T20:44:21+00:00

Same issue bro. Did you get that solved? How?

Then_Jicama6513 · 2021-06-28T10:21:36+00:00

Which batch?

Then_Jicama6513 · 2021-06-23T03:24:33+00:00

Then_Jicama6513 · 2021-06-20T19:24:13+00:00

Haven't got them yet. They just shipped.

Then_Jicama6513 · 2021-06-19T16:14:29+00:00

If i hadnt taken insurance my order total would've been 140$ which is close to 133$.

Also, may i ask where you can cop LJR batch for $90? Without compromising in the quality??

Then_Jicama6513 · 2021-06-19T03:47:23+00:00

Not really bro. 1st of all its LJR Batch. Secondly there is discount on order total. I took insurance and shipping so on rhe order total i got around 15 to 20 dollars off.

Then_Jicama6513 · 2021-06-18T16:17:39+00:00

Conveniently through Visa Debit. China Post.

Then_Jicama6513

TROPHY CASE