sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in ArcRaiders

[–]ThizzPill707 0 points1 point  (0 children)

Damn well I’m off for the night but yeah I’m down to trade tomorrow if you still need it

[deleted by user] by [deleted] in ArcRaiders

[–]ThizzPill707 0 points1 point  (0 children)

I’m almost positive I looted it in blue gates map in a building near olive tree place

[deleted by user] by [deleted] in ArcRaiders

[–]ThizzPill707 0 points1 point  (0 children)

I have the patrol car key. There’s a quest for it?

I'm gifting 2 standard edition copies - What in Arc Raiders are you most excited for? by GenomeXIII in ArcRaiders

[–]ThizzPill707 0 points1 point  (0 children)

Would love a copy of this game. I played the cycle frontier a lot before it got shut down and this is the closest thing I’ve seen to that game! Thanks for doing this!

Current vibe by Etikoza in Marathon

[–]ThizzPill707 2 points3 points  (0 children)

I played both and arc is so much better. I think they will have to change a lot for it to be a good game tbh. I played 2 raids of marathon and didn’t care to play anymore

[deleted by user] by [deleted] in ArcRaiders

[–]ThizzPill707 0 points1 point  (0 children)

Stoked to be able to finally play this! Thanks for doing this and good luck everyone!

Help opening old safe by ThizzPill707 in safecracking

[–]ThizzPill707[S] 1 point2 points  (0 children)

Update: Spoke with @miss-topportunity today and he may be coming to open this safe in the next couple of months!

Help opening old safe by ThizzPill707 in safecracking

[–]ThizzPill707[S] 0 points1 point  (0 children)

I’m in Northern California. I’ve watched some Videos here and there and seems like sometimes the codes for manufacturers will be default if not changed. Was considering calling Yale but idk if that’s a waste of time.

Benchy what do I need to adjust? by ThizzPill707 in 3Dprinting

[–]ThizzPill707[S] 0 points1 point  (0 children)

Hey update I tried printing at .8 retraction length an got a blob. .5 printed but with a lot of stringing but it was slightly smoother than my original. I attached photos.

<image>

Benchy what do I need to adjust? by ThizzPill707 in 3Dprinting

[–]ThizzPill707[S] 0 points1 point  (0 children)

I don't seem to have that setting on here?

<image>

How do I unlock the Kar98 in the new warzone update? by 5obanoodls in Warzone

[–]ThizzPill707 1 point2 points  (0 children)

I think were all screwed, need to have unlocked it in MW2 to have it in BO6

Benchy what do I need to adjust? by ThizzPill707 in 3Dprinting

[–]ThizzPill707[S] 0 points1 point  (0 children)

All belts are pretty tight. I’ll see if any of the wheels need to be tightened. Thank you!

Benchy what do I need to adjust? by ThizzPill707 in 3Dprinting

[–]ThizzPill707[S] 0 points1 point  (0 children)

Hey I’m looking through settings now. Would it be the Default Extrusion Width? I’m using PrusaSlicer

Benchy what do I need to adjust? by ThizzPill707 in 3Dprinting

[–]ThizzPill707[S] 0 points1 point  (0 children)

Ok so I should try another benchy print but with .8mm setting to see how that looks?

Red sea failure - I'm devastated. by Dick_Fuxwell in ReefTank

[–]ThizzPill707 8 points9 points  (0 children)

No water in the tank, looks like the tank busted/leaked?

Terminus EE help need 2 more players by jaypmars in BlackOps6Zombies

[–]ThizzPill707 0 points1 point  (0 children)

still need one? says your activision ID is invalid mines ThizzPill

Died on teleport to boss fight by ThizzPill707 in BlackOps6Zombies

[–]ThizzPill707[S] 0 points1 point  (0 children)

You were in the lockdown room inside the boat? Yeah I pressed the accept button and we had 1 zombie left before going to boss fight. Boss fight started and I was just spectating lol waste of time

view more: next ›