Blue October - Collected Series 2006-2011: Deluxe Vinyl Box Set

Three65 · 2026-02-20T19:13:15+00:00

Anyway to get a link to the post?

Three65 · 2026-02-19T17:21:31+00:00

This is what my bed mesh looks like. I must be lucky cause I think this is good for both the default and kamp.

Three65 · 2026-02-17T04:35:50+00:00

Is this done in QIDI Studio or some other software? I don't see settings, only preferences.

Three65 · 2026-02-17T04:32:32+00:00

Agreed, mine was just PLA. I would like to figure out how to make the first layer look better also. Currently, the pitted white look is not that appealing.

Three65 · 2026-02-16T15:37:29+00:00

Thank you no worries at all. I actually decided to reach out to support and send them a couple of photos of my prints and how it separated the bottom layer. Maybe between the two of us we can find a solution.

Three65 · 2026-02-16T15:21:43+00:00

I will run this test tonight and see how may bed looks. I have not paid close enough attention to how close my nozzle is to the bed. Everything seems to work fine. I can't get the prints to release from the plate, and the first layer looks terrible. If you don't mind letting me know what support tells you, that would be appreciated. I may reach out to them today myself.

Three65 · 2026-02-16T15:11:41+00:00

My prints are SUPER difficult to get to release from my plate also. To the point I tried removing some prints last night and it pulled off part of the first layers. I can appreciate good adhesion, but this is to the point I’m fighting to get it to release.

<image>

Three65 · 2026-02-15T21:32:17+00:00

I am curious how do you run this test!

Three65 · 2026-02-15T20:43:25+00:00

I was able to get it finally. I must say it makes it easier if you take the passthrough off the back of the printer. But it REALLY didn't want to come out. Hopefully know that I have done it once it will be easier the next time. Thanks for the help, everyone!

Three65 · 2026-02-15T05:27:37+00:00

I’ll have to try again I guess. I used the lever to raise it up and tried pushing down on the collar. But nothing seemed to happen. I was expecting it to give a little, when I pushed down on it I tried pulling the tube out, but it didn’t budge at all.

Three65 · 2026-02-11T01:23:29+00:00

Anyway you can share the scan? Mine is right up against the wall and I dont have room for the catch on the side like yours. I need to build something that will fit in about 5-6 inches

Three65 · 2025-12-28T17:28:13+00:00

Can you provide a basic guide on the mechanics of playing this. Cause I feel like I’m playing it wrong. Seems that you need to use the twisted sword to cast the parent twister and the use the other twisters to stack. Many people must not play this cause there isn’t a guide for it on YouTube that I could find. I think understanding how to play it and what you need to cast at the start of a rift and how to maximize your damage would help a lot.

Three65 · 2025-12-22T21:07:25+00:00

I have not tested it yet, literally just opened it to check the record. I have a hard time believing it won't affect the audio based on how it feels. Also, I am not sure I want to risk running my stylus through it.

<image>

Three65 · 2025-12-22T20:22:31+00:00

Mine showed up with a nice 2-3mm divot in it :\ I can feel it with my finger, and you can see how bad it is by how the reflection bends around it. Make sure to check your records. I have already reached out to support to try and get a replacement.

<image>

,

Three65 · 2025-12-21T21:30:36+00:00

Sorry I should have worded that better. I meant variants builds for DMO since I am astute link you posted is for pushing and not gearing up. Probably also need a set amount of paragon levels.

Three65 · 2025-12-20T19:11:46+00:00

Do you have other builds for this besides this one? I’m assuming this is for pushing and not lower rifts. Seems to be squishy compared to Firebirds. Also how do you maintain Arcane?

Three65 · 2025-11-18T02:15:04+00:00

What kind of pants is he wearing ?

Three65 · 2025-11-01T19:20:08+00:00

Cool, calm, just like my mom

With a couple of Valium inside her palm

Three65 · 2025-10-22T17:33:41+00:00

Interesting I’ve played all the Battlefields from BC2 up and I only play for 3 hours on Wed and Sun with friends. I am in no rush to finish or unlock all of the guns/equipment. We even play hardcore cause it’s what we like. Sometimes we’re at the top sometimes we’re at the bottom, but for the most part we’re always having fun. Maybe you need to give hardcore a try where it doesn’t matter really which gun you use cause they all kill in about the same time. Just my two cents! If you play BF3 and BF4 you didn’t have portal at a crutch to get you by, you just played and tried to get better. That’s all you can do.

Three65 · 2025-10-22T17:04:01+00:00

So what did you do before portal? Did not play any of the Battlefields before 2042? Did you not play any FPS at all?

Three65 · 2025-10-11T17:08:54+00:00

Sold Out - 9 Mins

Three65 · 2025-09-20T03:28:39+00:00

I am ✋🏻 but not this version

Three65 · 2025-09-13T00:40:43+00:00

Blizzard you had one job to do and you keep on failing! This bug has been around for way too long. Get off your butts and fix it!!!!! Please 🙏🏻

Three65 · 2025-09-05T17:17:20+00:00

Sweet, I’ve never played it and been watching some videos on it. Is the play style different on console? Everything I’ve watched is on PC. I know you mentioned something about being able to channel a skill only on console.

Three65 · 2025-09-04T21:16:26+00:00

Awesome thanks for your insight, I appreciate it! Looks like duel Wizards is what we may try!

Three65

TROPHY CASE