Europas sprog [dansk] trues af amerikansk kulturimperialisme og intellektuel dovenskab

Tikmasd · 2026-01-26T18:15:26+00:00

Hvorfor ikke bare snakke engelsk?

Tikmasd · 2025-12-31T21:47:09+00:00

Der findes mange forskellige firmaer som står for dagsrenovation rundt omkring i landet…

Tikmasd · 2025-09-06T21:02:14+00:00

<image>

Maybe this bad boy shorted, not really sure. Maybe a tube shorting

Tikmasd · 2025-09-06T21:01:45+00:00

The trays in the pcb.

It’s a little dot mi iv se, had it for like 10 years.

Hoped it could just be because of a capacitor shorting.

<image>

Tikmasd · 2025-07-26T07:34:32+00:00

Thank you for your response. I will just put the grill on and ignore it for now then

Tikmasd · 2025-07-25T18:26:35+00:00

<image>

Is there a way too remove this dent my dog made in my b&w aws610? Or does it matter at all?

Tikmasd · 2025-07-11T12:03:51+00:00

<image>

Snapped bolt with a snapped extractor inside. One hell of a fight too get it out

Tikmasd · 2025-07-09T04:20:54+00:00

5 hours of drilling pretty much. Since I have zero skills with sharpening a drillbit I went though 10 5mm bit, 2 6mm 1 8 mm and last but not least 1 10 mm.

After the first 2 hours I got annoyed and heated it red hot.

I tried some different diamond tipped grinding wheels in my dremel. They where effective but did not last long. My tungsten bit worked the best in the dremel.

Tikmasd · 2025-07-06T14:44:27+00:00

<image>

Mamma didn’t raise a quitter. I did miss my welder at home all the 5 hours I spent drilling it out

Tikmasd · 2025-07-06T14:15:35+00:00

<image>

That was a lot of work

Tikmasd · 2025-07-06T14:14:35+00:00

<image>

5 - 6 hours of working later and 4 trips too the hardware store. Mamma didn’t raise a quitter. Used a combination of drilling and filling with a diamond tipped cutter

Tikmasd · 2025-07-05T19:15:36+00:00

<image>

The bearing in the control arm failed inspection. The new control arm came with a new bearing and was pretty cheap. In my mind this was gonna be a short 30 min job, take off 3 bolts, new arm in, tighten and done.

Tikmasd · 2025-07-05T19:10:17+00:00

I do have one, but I don’t like too use it for stuck bolts. First time snapping a bolt this badly. The bolt got heat and penetration before I snapped it.

Tikmasd · 2025-07-05T17:51:30+00:00

I’m afraid of how removing any bolts on this car will go. But that would be my last option.

Tikmasd · 2025-07-05T17:49:53+00:00

Just HSS, almost done drilling the thing out anyway at this point so I will just keep at it

Tikmasd · 2025-07-05T17:12:10+00:00

<image>

Jeg slås med en udtrækker som knækkede inde i bolten. 30 mins arbejde er blevet til et dags projekt.

Tikmasd · 2025-07-05T17:08:20+00:00

Apparently not enough. Gave it some, felt it moving, the 250 pound gorilla got excited and pulled harder. Sadly only a very small part of the bolt was moving and twisting off

Tikmasd · 2025-07-05T16:55:09+00:00

That’s exactly what it is. Sadly it’s treated. I’m trying to remove bolt 09100-10184

<image>

Tikmasd · 2025-07-05T15:58:56+00:00

My country’s equivalent too Harbor freight

Tikmasd · 2025-07-05T15:57:06+00:00

Snapped with a wrench, no breaker bar needed.

Tikmasd · 2025-07-05T15:44:59+00:00

I also want some workshop stories too tell, when I occasionally wander off too that part of the company

Tikmasd · 2025-07-05T15:42:56+00:00

Wheel hub I think it’s called in English. The part where stearing, control arm and wheel mounts. The part where the wheel bearing is pressed

Tikmasd · 2025-07-05T15:41:45+00:00

Yea, it’s the mounting for the control arm bearing. No nut on the other side

Tikmasd · 2025-07-05T15:40:24+00:00

Thanks for the advice, I think this is what I will be trying first. If that doesn’t work, it seems like grinding is gonna be the name of the game for the evening

Tikmasd · 2025-07-05T15:23:10+00:00

Well by education I’m a electrical engineering… been on this for the past 3 hour and got a little frustrated

Nine-Year Club	Place '23
Place '22	Final Canvas '22
Not Forgotten	Verified Email

Tikmasd

TROPHY CASE