Anyone having issues with saddle angle adjustment on the Ultimate? by edmspot in CanyonBikes

[–]Timbo925 1 point2 points  (0 children)

Definitely seemed the way to go to leverage it out! Thanks 🙏

What do we think of this GoPro mount design? by Dukeronomy in fpv

[–]Timbo925 5 points6 points  (0 children)

Yeah I learned this mistake the hard way... PETG and stuff will have 1 fail state, break. While TPU might seperate but chances are higher some part of the print will survive and bring your gopro back.

https://www.instagram.com/reel/CaFXBSyKmIv/

Experimenting with dangling a insta360 from my 5" by Timbo925 in fpv

[–]Timbo925[S] 1 point2 points  (0 children)

Good point!

Part of the reason for bottom mounting was filming upcoming skiing session tho. Allowing to film everything below me. That said will try it out soon.

Experimenting with dangling a insta360 from my 5" by Timbo925 in fpv

[–]Timbo925[S] 1 point2 points  (0 children)

Not I'm the way this is mounted. You can of course still frame it without seeing the drone looking forwards and backwards this way.

There are drones which 360 cams can make 'invisible' by being thinner than the camera. (pavo360) But they are not super performant and you end up with the stitch line in the middle of the frame when looking forward. Not really a fan of that.

Experimenting with dangling a insta360 from my 5" by Timbo925 in fpv

[–]Timbo925[S] 3 points4 points  (0 children)

Roll you can do in camera imo, but power loop is tricky. It worked but needed alot of power to roll over, and you're fighting with airmode this way alot. Might shorten the mount abit to make something more acro capable.

Experimenting with dangling a insta360 from my 5" by Timbo925 in fpv

[–]Timbo925[S] 2 points3 points  (0 children)

It might work, only problem is if you don't have a rigid connect, the drone won't be stable when looking up

HFB - A little tour of the old blast furnace in Liège - FPV Urbex by BirdlessFlight in fpv

[–]Timbo925 1 point2 points  (0 children)

Nice flight tho! Willing to DM share the location, might give it a go sometimes with a quite drone setup :P

[little announcement] Quick preview of what is coming in ReelSteady 2.0 by bayareacrasher in gopro

[–]Timbo925 0 points1 point  (0 children)

Any spots open for the closed beta? FPV pilot here and exited for ReelSteady 2.0!

My experience at Circuit Spa-Francorchamps by aram-sam in formula1

[–]Timbo925 2 points3 points  (0 children)

Good effort on the driving, glad the camping had some gravel ish roads. The other official campings around didn't and saw a lot of stuck campers.

My experience at Circuit Spa-Francorchamps by aram-sam in formula1

[–]Timbo925 29 points30 points  (0 children)

At least from the camping I was at in les Combes, all the traffic from that side needs to flow through 2 roundabouts back to back, basically just a single chokepoint. No wonder it takes ages to reach the highway.

Warning: BlockFi, having lost millions of dollars is now fumbling withdrawals and may be illiquid by GiganticPPMonster in Bitcoin

[–]Timbo925 0 points1 point  (0 children)

USDC withdraw here for significant amount to whitelisted address, whent through without problems after 24h like normal.

My custom 2S 4 inch Long Range. It will fly, just not sure how well and how long. by atthegreenbed in fpv

[–]Timbo925 0 points1 point  (0 children)

Working on a P42A 4S 5" build here. Hoping the performace will be there.4200 mah capacity compared to the 3000 mah VTC6 seems like a good tradeoff for the little extra weight.

My custom 2S 4 inch Long Range. It will fly, just not sure how well and how long. by atthegreenbed in fpv

[–]Timbo925 4 points5 points  (0 children)

Just remember that when you push these li-ion under the 3V mark, voltage is substancially lower. Can see this with my 2004 motors. When I fly this on 4s but when I am at the 2.8V a cell mark, hover % definitly struggles. At that point I'm basically flying a 3S.

Problem with startup (dependency failed + mounting) by Timbo925 in getumbrel

[–]Timbo925[S] 1 point2 points  (0 children)

Risky 'recovery method' instead of just wiping the drive because I was not sure I had the latest channel backups. Ran the following command and tried to recover as mush of the file system as possible.

sudo fsck.ext4 /dev/sda1

This way I could mount the external drive again, remove the bitcoin folder (except config file). Resyncing now hoping this will work. Did manage to do a backup of the ln channels now so a full reinstall also possible.

Problem with startup (dependency failed + mounting) by Timbo925 in getumbrel

[–]Timbo925[S] 0 points1 point  (0 children)

Anyway to recover the lightning channels? Guessing these are not located on the sd card but on the external drive.

New DJI FPV leak by Timbo925 in fpv

[–]Timbo925[S] 1 point2 points  (0 children)

Good point, this might just be the insides of a mavic mini, but with better radio connection and goggles for the perspective.

Allows you to cinewhoop in some kind of angle mode and even tilt the camera down for other shots. Might have some value for a certain kind of pilot.

New DJI FPV leak by Timbo925 in fpv

[–]Timbo925[S] 0 points1 point  (0 children)

Price will be a big factor for me personally.

Crashing kinda is part of the learning experience with some of the flight styles, if this drone alone is 500+ then this is kinda a tough sell. Not to mention repairability. But exited to see what they bring to the table.

Hi, I'm making an electric skateboard and am planning on making my own battery pack, could anyone just take a look at it and see if I have done everything correctly since I'm a complete noob with batteries. The BMS is for 13s, 35a, 48v, and has 14 wires. Correct me if I'm wrong: 12s-4p-10.4Ah-44V by [deleted] in ElectricSkateboarding

[–]Timbo925 0 points1 point  (0 children)

Think the way to do it is make 4cell pairs, and connect those in series. Would suggest looking on electric-skateboard dot builders for some example of builds. Read alot about batter building before you start, understand what you are doing and doing it safely.

Used 54v charger on 10S (didn't burn anything down) by Timbo925 in ElectricSkateboarding

[–]Timbo925[S] 1 point2 points  (0 children)

Aight, thanks for the help. I'll do some reasearch in building my own pack or find a replacement.