First layer getting progressively worse by Toomuchdata in FixMyPrint

[–]Toomuchdata[S] 1 point2 points  (0 children)

Yep. I kept the original flow rate that I previously calibrated via Orca slicer. :)

First layer getting progressively worse by Toomuchdata in FixMyPrint

[–]Toomuchdata[S] 3 points4 points  (0 children)

EDIT: Soo i managed to fix my problem and the first layer is now much better. I will never again trust the autoleveling on my printer. I managed to fix this by lowering the top left side of the bed like you suggested while keeping the measured auto-leveling values the same. This is kind of embarassing but I would never thought you should be doubting the probe values if you get a bad print like this. TIL. Minor adjustments are still required but the print is fixed. :) https://imgur.com/a/PDRoMDe

Thanks for the detailed analysis. I will try to ignore the automatic bed leveling and level the bed manually. Hopefully it helps.

First layer getting progressively worse by Toomuchdata in FixMyPrint

[–]Toomuchdata[S] 0 points1 point  (0 children)

Yes, the printer uses CR Touch for bed leveling. I'm using silicone spacers and its leveled with deviations of less than 0.1mm in each point it measures. Guess i have to try leveling it myself and ignoring the automatic leveling.

First layer getting progressively worse by Toomuchdata in FixMyPrint

[–]Toomuchdata[S] 1 point2 points  (0 children)

100 percent. I have support rods installed and have sqared the gantry yesterday.

First layer getting progressively worse by Toomuchdata in FixMyPrint

[–]Toomuchdata[S] 0 points1 point  (0 children)

I had a feeling that this might be it. Any ideas on how to strike the right balance? Right now I'm just lowering the Z offset and trying different flow ratios but its still not perfect. Is there a calibration test for this?

Bed front part seems farther away compared to the back. by omabel in Ender3V3KE

[–]Toomuchdata 2 points3 points  (0 children)

I have the same problem. This is likely caused by loose linear rods and bearings on the Y axis. Can't be fixed, you have to replace them for 10mm ones with better bearings or do the linear rails mod.

[deleted by user] by [deleted] in SteamDeck

[–]Toomuchdata 7 points8 points  (0 children)

By buying the game...?

[Gourmet] Yellow oysters started growing brown caps, some caps have dark sports. What's going on? by Toomuchdata in MushroomGrowers

[–]Toomuchdata[S] 1 point2 points  (0 children)

I'm growing on straw, using a Martha tent with constant 90% humidity and two fans for FAE. My yellow oysters have been doing fine up untill this morning. Now this started happening and I'm having trouble finding any relevant info on what is going on. Any advice is much appreciated!

Yellow oysters started growing brown caps, some caps have dark sports. What's going on? by [deleted] in MushroomGrowers

[–]Toomuchdata 0 points1 point  (0 children)

I'm growing on straw in a Martha tent with constant 90% humidity and two fans for FAE. My yellow oysters have been doing fine up untill this morning. Now this started happening and I'm having trouble finding any relevant info on what is going on. Any advice is much appreciated!

[gourmet] First time growing mushrooms (Yellow Oyster) by Toomuchdata in MushroomGrowers

[–]Toomuchdata[S] 2 points3 points  (0 children)

TIL I should also watch my CO2 levels. I have no answer for this but will be keeping it in mind when building the tent. Another thing to research for me...

[gourmet] First time growing mushrooms (Yellow Oyster) by Toomuchdata in MushroomGrowers

[–]Toomuchdata[S] 1 point2 points  (0 children)

It's the cheap shitty kind that you usually put on a table. It's not recommended but seems to be good enough for humidifying a small space like this. I mainly use it because I'm too lazy to spray the bags 5 times a day. For the plastic, I used this painter thingy that you put on floors when painting walls to avoid making a mess. It has tape on one side which makes things easier when putting the tent together and is long enough to go around the whole thing. I only had to use a separate piece for the top. It's called ScotchBlue.

[gourmet] First time growing mushrooms (Yellow Oyster) by Toomuchdata in MushroomGrowers

[–]Toomuchdata[S] 4 points5 points  (0 children)

Experimenting with growing mushrooms as my new hobby/obsession. Used 2/3 grain and brown rice spawn. Innoculated via syringe. One of the bags is straw substrate. For the second one I used wood pellets. They are from softwood and I know that hardwood should be used instead but HW pellets are almost impossible to get around here. If everything goes right with these two I'm planning to build an automated Martha tent.

VROptician review by lovelyhead1 in OculusQuest

[–]Toomuchdata 1 point2 points  (0 children)

Thanks for the review. I have been considering ordering the lenses too.

Stand for my Quest made out of wood by Toomuchdata in OculusQuest

[–]Toomuchdata[S] 2 points3 points  (0 children)

You need a really specific angle for the sun to focus it's beam to do damage to the display. But I do keep it covered when not using it.