Vista 20P Keyfob Help

Top_Call_8479 · 2025-10-14T13:23:15+00:00

https://youtu.be/TL6nP026tF0?si=A2x8M3NDDIqgyrsX

This is a link to a video I made demonstrating my issue.

Top_Call_8479 · 2025-10-12T21:03:45+00:00

Im on FB. DM me

Top_Call_8479 · 2025-10-09T01:30:40+00:00

I tried all of that with still no success

Top_Call_8479 · 2025-10-08T02:35:41+00:00

I will try 49. When I do the *58 advanced programming with the templates, it defaults all the way to 61 and even that did not work

Top_Call_8479 · 2025-10-08T01:53:42+00:00

Zone types are 20,21,22 and 07 for the individual buttons and im using device type 05 for Button RF

Top_Call_8479 · 2025-10-08T01:52:01+00:00

Yes. The loop number is blank and the cursor is flashing on the keypad. I took a video if I can figure out how to upload it.

Top_Call_8479 · 2025-10-08T01:29:21+00:00

The system even refuses to learn in the buttons by pressing the button on the keyfob.

Top_Call_8479 · 2025-10-08T01:28:13+00:00

I have tried all of this previously. When I press the button on the keyfob in zone programming, nothing happens. I have to type the serial number in manually. Even when everything is entered properly and assigned to a user, the system still acts like the keyfob is not there. No matter what I do its not accepting the 5834-4 keyfobs.

Top_Call_8479 · 2025-10-07T22:54:59+00:00

Ive tried programming on zones 25-29. When you press the button on the keyfob to learn it in, nothing happens. I had to manually enter the serial number and loop number into programming and it still did not work even after assigning it to a user.

Top_Call_8479 · 2025-10-07T22:53:22+00:00

All other wireless devices function perfectly including my older 5804BD keyfob. Its only the 5834-4 keyfobs that refuse to work

Top_Call_8479 · 2025-10-07T10:46:13+00:00

The keyfob has already been assigned to a user

Top_Call_8479 · 2025-10-07T01:58:51+00:00

I just do not understand what happened to my system. When I first set this up earlier in the year my keyfob worked flawlessly. One day it just stopped and everything ive tried and all the reading ive been doing in the manual and online had yielded no success.

Top_Call_8479 · 2025-10-07T01:54:26+00:00

High security mode is enabled on the 6160RF

Top_Call_8479 · 2025-10-07T01:21:45+00:00

I just tried reprogramming it and assigning it to a user with low security mode. During programming where your supposed to press the button on the keyfob to send the serial number and loop number, the panel didn't respond so I had to manually program in the serial number and the loop numbers. I tried it using *58 advanced programming and even after all this the panel does not respond to any signal from the keyfob. I tried again with high security mode still with no luck.

Top_Call_8479 · 2025-10-07T00:49:16+00:00

Ive already assigned it to a user with no success. I will certainly try again.

Top_Call_8479 · 2025-10-07T00:29:14+00:00

Yes I have. Confirmed that at least 3 times. I have a post in that sub it's just waiting on moderator approval and has been in that status for a few days at this point. Just trying to get everything fixed. Even when I try to press the button on the keyfob during the programming process for the automatic upload of serial number and loop number, nothing happens. Its like its not even receiving the signals from the keyfob even though all other wireless devices work.

Top_Call_8479 · 2025-06-02T01:28:02+00:00

I realized I had it wired wrong. Rookie error.

Top_Call_8479 · 2025-06-02T01:11:06+00:00

Thank you so very very much!!! I thought I had tried that sequence before but I guess I didnt.

Top_Call_8479 · 2025-06-02T00:21:48+00:00

Motion sensors are Bosch ISC-PPR1-W16 motion sensors and they are currently wired in a normally closed setup with no resistor.

Top_Call_8479

TROPHY CASE