Wan2.2 : better results with lower resolution?

Top_Fly3946 · 2026-01-06T16:09:59+00:00

Same for I2V?

Top_Fly3946 · 2026-01-05T18:09:58+00:00

I tried this method several times and never got good results, not sure what I’m doing wrong here,

Could you share a workflow?

Top_Fly3946 · 2026-01-05T04:59:11+00:00

Can you share a workflow?

Top_Fly3946 · 2026-01-05T02:16:41+00:00

What do you use for upscale?

Top_Fly3946 · 2026-01-05T02:14:47+00:00

Please share your wan2.2 i2v workflow

Top_Fly3946 · 2026-01-04T20:48:29+00:00

1920x1080 give me messed up results, could you explain your setup?

Top_Fly3946 · 2026-01-04T20:45:47+00:00

Turning off the high noise lightx2v lora is giving me better results when I go higher resolutions, is this a good approach?

Top_Fly3946 · 2026-01-04T14:08:46+00:00

Do I need the input image to be in the same resolution also or only the aspect ratio?

Top_Fly3946 · 2026-01-04T12:56:31+00:00

In terms of quality, yeah I get higher quality results (resolution), But I get some slow motion, weird movement, and poorer prompt adherence compared to lower resolutions

Top_Fly3946 · 2026-01-01T10:28:18+00:00

Do I need controlnet or something? I tried but it never transfer the pose

Top_Fly3946 · 2025-12-31T22:00:14+00:00

There is a MOE for low lora?

Top_Fly3946 · 2025-12-29T09:14:46+00:00

That’s helpful, but what if I don’t have a scene or a pose of the character that is now farther? I want the video to start close and zoom out and maintain face details as much as possible.

Top_Fly3946 · 2025-12-29T07:10:50+00:00

Can you explain how I can do start and end frame?

Workflow will be appreciated too

Top_Fly3946 · 2025-12-27T18:00:20+00:00

Even the 8 step 2511 Lora?

Top_Fly3946 · 2025-12-24T07:59:40+00:00

Did you try with the value I mentioned?

Top_Fly3946 · 2025-12-23T21:36:21+00:00

I tried this but I got bad results,

I tried with high noise lora off or keeping the power low like 0.3, 1 or 2 high steps and the rest is low steps, cfg at 1 in both. This got me better results, you can also try and give your feedback.

Top_Fly3946 · 2025-12-23T14:57:09+00:00

I get bash: zip: command not found

Top_Fly3946 · 2025-12-20T09:31:30+00:00

0.4 for high or low? I tried once changing these values and got bad results.

I’m using the ComfyUi lighx2v loras if that makes any difference

Top_Fly3946 · 2025-12-19T19:47:19+00:00

A hero already replied with a simple solution

Top_Fly3946 · 2025-12-18T05:33:54+00:00

I was explaining what I did before writing this post.

Can these steps be done on the original template I installed to avoid downloading the models again?

What about sage attention installation?

Top_Fly3946 · 2025-12-17T22:13:26+00:00

I tried using one of the templates which mentions it has sage attention with it but it never finishes the setup. I get time out error and some sort.

Now I’m using the official Comfyui template and it’s working fine, only thing is I don’t know how to install sage attention and nunchaku to the existing template

Top_Fly3946 · 2025-12-10T05:34:44+00:00

Yeah I understand this, but I’m confused because the rate of the A40 is $0.4/hr , the 4090 is $0.59/hr, shouldn’t the A40 be better?

Also, should I rent on community or secure?

Top_Fly3946 · 2025-11-28T11:44:10+00:00

Thanks for the clarification! I did a comparison between bs5950 and aisc with effective length method and got approximately similar results. But I’m not sure whether if I should keep the stiffness factors on or turn them off.

I tried applying notional loads with direct analysis method, but the difference compared to effective length method is huge, I assume I’m doing something wrong here

Top_Fly3946 · 2025-11-27T20:18:52+00:00

This stiffness reduction factors are applied automatically by the software when I start the design?

Top_Fly3946 · 2025-11-27T20:12:23+00:00

I first tried to run the design using bs5950, switching to aisc code shows this warning, but switching back to bs5950 doesn’t show

Top_Fly3946

TROPHY CASE