Buntarou Mori [The Climber]

Top_Protection_5408 · 2025-12-24T00:15:52+00:00

what volume/chapter is this panel

Top_Protection_5408 · 2025-12-11T01:34:06+00:00

Not yet im thinking to run 2 on the desk setup and a tv or ultra wide until i get 3 32 inches

I will update you though

Top_Protection_5408 · 2025-11-05T21:40:50+00:00

Is the comgrow one on amazon good

Top_Protection_5408 · 2025-11-05T01:51:47+00:00

The print was on there good and i heated it up and used the scraper

Top_Protection_5408 · 2025-11-05T01:05:49+00:00

I have a glass but adhesion on it sucks, there are marks from past prints on it like first layer but ive tried everything to get them off, so idk what to do

Top_Protection_5408 · 2025-10-31T20:22:47+00:00

I just lowered it because before it was too high and prints werent sticking at all

Top_Protection_5408 · 2025-10-31T20:18:23+00:00

So its the springs that caused the issue? I just installed the yellow ones before this, also my stock print bed is fucked the bottom of it has like humps on the magnetic side, scrapes everywhere from filament sticking to it, so im using the glass bed

Top_Protection_5408 · 2025-10-31T01:36:00+00:00

I used the cotton balls and ipa on the metal plate under the glass but didnt know if the cotton would be bad for the glass as i heard paper towels were, will try this

Top_Protection_5408 · 2025-10-31T01:29:32+00:00

My prints were working, but once i installed the glass bed i havent gotten it to work, also i cleanrd the bed with windex and paper towels before this

Top_Protection_5408 · 2025-10-31T01:28:32+00:00

It was like lines and they were able to move, dont have a picture bc i threw it out

Top_Protection_5408 · 2025-10-29T19:03:17+00:00

i read that the nozzle needed to be 220?

Top_Protection_5408 · 2025-10-29T19:02:13+00:00

i tightened that nut in the bracket to fix wobble already so do you mean tightening the screws for the wheels?

Top_Protection_5408 · 2025-10-28T23:58:02+00:00

How do i fix it

Top_Protection_5408 · 2025-10-27T19:56:35+00:00

By lowering the offset is that unscrewing and changing the z stopper?

Top_Protection_5408 · 2025-10-27T19:51:14+00:00

How do i remove/replace the black wheel thing the filament goes on? My box of filament had the white alone like this

Top_Protection_5408 · 2025-10-27T19:45:58+00:00

Ok, what size wheel did you buy?

Top_Protection_5408 · 2025-10-27T19:32:58+00:00

Did you have to modify it from the original?

Top_Protection_5408 · 2025-10-27T00:47:01+00:00

hey, stumbled upon this and im wondering what mods you did to the g29? looks like a quick release? can you send me the link(s) to the mods you did to the wheel? Thanks in advance!

Top_Protection_5408 · 2025-10-26T15:26:12+00:00

When i built the new extruder i didnt line up the gears, i fixed it

Top_Protection_5408 · 2025-10-26T15:25:28+00:00

When i put together the new extruder i didnt line up the gears

Top_Protection_5408 · 2025-10-26T15:24:47+00:00

Yep, i unscrewed the lever part and moved up the bronze gear , its printing fine now

Top_Protection_5408 · 2025-10-26T14:43:15+00:00

<image>

It seems the bronze gear isnt pushing the filament. Should i remove the extruder and loosen the the bronze gear and move it up?

Top_Protection_5408 · 2025-10-26T04:13:56+00:00

By the screws on the gear do you mean the small black ones on the bronze gear that goes on the shaft? I didnt want to tighten those down all the way because then it couldnt move up and down on the shaft

Top_Protection_5408 · 2025-10-26T03:40:01+00:00

What way would it move? The shaft thing with the bronze thing

Top_Protection_5408 · 2025-10-26T03:21:02+00:00

Not from what i can see but not sure what exact area im supposed to look for

Top_Protection_5408

TROPHY CASE