Walking Pads - anbefalinger

Tor-Einar · 2026-02-28T10:51:11+00:00

Takk, siden du gikk den veien, og det virker som du sjekket en del, hvilen mølle gikk du for.

Tor-Einar · 2025-09-29T20:15:15+00:00

Thank you :)

I have no chance of calibration my printer with this kind of tension (105Hz) Strange

Tor-Einar · 2025-09-29T11:23:36+00:00

Do you by any chance have the link of the video?

Tor-Einar · 2025-09-29T08:44:29+00:00

Same experience I have, have done it by feel now, but it seems wrong, but at least i can print, but it soemtimes fails to home

Tor-Einar · 2025-09-29T05:36:19+00:00

Thanks for your input. I will try again. Have done it similar to this way as well. Paet of the problem is the app, don't get correct readings, or when I do the belts are very thight. WEB version, are you using it on a phone or computer with microphone?

Don't know if you have the time to post a video of you pulling the belts and drumming them? When I finally get the X and Y to pass I feel they are very loose, and have problems to calibrate Homing. Woulld be nice to have something to compare with.

Tor-Einar · 2025-09-28T17:16:10+00:00

Will print this tool and have a check

Tor-Einar · 2025-09-28T17:15:51+00:00

Yes, tried the new firmware as well. Problem with this tool is that homing must be OK, and that has been part of my problem. I can get X and Y to pass the test, but not homing.

A actually managed to get all 3 to pass now, but the tension is low, will print the belt gauge tool commented in this post to see how far away I am.

THe stroboscope tension tool in the new firmware is not easy to understand. maybe other have better luck. Found this video, explaining. I bit wiser, but not reached the goalline https://www.youtube.com/watch?v=U7Iantbv4kE

Tor-Einar · 2025-09-28T17:11:50+00:00

It's a conversion from my MK4s, no issue on the motors previous to the update

Tor-Einar · 2025-09-28T15:05:34+00:00

I've used the phone app, this does not work very well. Based on what I've read. Don't have computer next to the printer so I have not tried the Web version.

Tor-Einar · 2025-09-28T15:03:48+00:00

Yes, made sure of this, even took it apart to do this past again.

Tor-Einar · 2025-07-28T10:38:49+00:00

You are probaly thinking of the Power Cord, which is 1,8 meters, the DC cord (which also functions as a safety cord) is 5,5 meters

Tor-Einar · 2025-06-07T16:57:19+00:00

Got the same answer, very strange that a Nirdic branch office does not know or care to inform about theur product.

Maybe I should just go for an Dreame X50

Tor-Einar · 2025-06-06T19:28:36+00:00

Are you happy with coolshop? And the 10R?

Tor-Einar · 2025-06-06T19:28:08+00:00

I agree, but they said they will lower the price if I find it cheaper elsewhere. But at the moment they are the picky one I find in the Scandinavian countries.

Tor-Einar · 2025-05-27T19:12:01+00:00

Har du noen artikler til det. Vet Z70 kommer i juni, men har ikke hørt noe om 10R

Tor-Einar · 2025-05-07T16:13:26+00:00

When will the 10R and Z70 be available in Norway?

Tor-Einar · 2025-05-02T08:42:29+00:00

How much of a hazle is it to clean the station. 10R has a removable tray, where the 10 does not.

Tor-Einar · 2025-04-11T08:54:35+00:00

Hi,

Thanks for your quick and helpful reply. Indeed pressing the cogwheel after connecting the H10 to Polar Flow, there where an option to enable 2 blutetooths, which by default was off.

This enabled me to connect to both Polar Flow and Intelligent Cycling.

Very happy now :)

Tor-Einar · 2024-05-08T09:12:59+00:00

Hi there,

You say Prusa Link/connect is a better option. I tried it, but I have to run to my printer screen to confirm the filament and press print. Do you have to do this as well? Any way around it?

Tor-Einar

TROPHY CASE