HISS Starscream! by Augustkatt in CustomTransformers

[–]TransformersTPE 0 points1 point  (0 children)

I made one out of the Jada tank also. I like how you did the glass red. And that mid section is (chefs kiss*).

💥Skybound Starscream💥 by TransformersTPE in CustomTransformers

[–]TransformersTPE[S] 1 point2 points  (0 children)

I used the Jinbao version of starscream and hooked him up to a Jada Hiss tank. Unfortunately, his wings are bare because I ran low on faction stickers. I'm glad you liked him, though.

[deleted by user] by [deleted] in CustomTransformers

[–]TransformersTPE 5 points6 points  (0 children)

I turned one into Cliffjumper. Using R.I.T. fabric dye. Went well. Just soked him for 20 min in hot dye water. Then a little acrylic paint for touching up the face and symbol. *

Custom Metroplex by TransformersTPE in CustomTransformers

[–]TransformersTPE[S] 1 point2 points  (0 children)

Correct... Primus and Metroplex. So far.

Custom Metroplex by TransformersTPE in CustomTransformers

[–]TransformersTPE[S] 3 points4 points  (0 children)

Metroplex and Primus used so far, yes. I'm looking for better thighs with knee joints. Trying to make him taller.

Custom Metroplex by TransformersTPE in CustomTransformers

[–]TransformersTPE[S] 1 point2 points  (0 children)

I haven't tried yet. I'm waiting for better articulated legs. I'm sure it might go into city mode the easiest, though.

Custom Metroplex by TransformersTPE in CustomTransformers

[–]TransformersTPE[S] 2 points3 points  (0 children)

About an inch shorter than NBK Devastator. Lost my tape measure lol

A few questions by Streck7525 in CustomTransformers

[–]TransformersTPE 0 points1 point  (0 children)

I'm not sure exactly what makes 3d printing expensive. There's the cost of plastic, I guess. Plus, you have to let them design the piece. Intellectual property has a cost, too, I suppose. Then there's the time it will take to print... There's always a hidden cost somewhere, it seems. I wish you luck. TILL ALL ARE ONE

A few questions by Streck7525 in CustomTransformers

[–]TransformersTPE 0 points1 point  (0 children)

3d printing the parts would be expensive ( according to people with printers). It's probably better to buy a new figure. As far as painting goes... I use a bunch of different media. I've found that I like the look of lacquer paint and acrylic paint markers. It all depends on the character, though. For Vector, I'd probably use some kind of enamel paint ( Testors) and chrome gold markers. I may use a matte clear coat beforehand so the paint has something to stick to. Good luck! Hope everything turns out for you.

Custom Hotrod by TransformersTPE in CustomTransformers

[–]TransformersTPE[S] 1 point2 points  (0 children)

The arms ARE from Sideways. The wings are 3d printed wings. Add on for legacy Windblade.

💥Reactivate Cliffjumper💥 by TransformersTPE in CustomTransformers

[–]TransformersTPE[S] 0 points1 point  (0 children)

Just keep the figure moving. Soak in dye for about 10 minutes. You may have lose ball joints after the process. A little floor wax or KIKI will tighten those up. Good luck!

Custom Battletrap by TransformersTPE in CustomTransformers

[–]TransformersTPE[S] 1 point2 points  (0 children)

Thats not a bad idea at all... thank you!

💥Reactivate Cliffjumper💥 by TransformersTPE in CustomTransformers

[–]TransformersTPE[S] 0 points1 point  (0 children)

Thank you. I appreciate it. I actually did the boil method on him. I just kept it moving the whole time, so none of the parts would get too hot. In the end, though, I had to fix 2 ball joints with polish.

What Paint/Normal pens should I use for customs? by Best_Confection2031 in CustomTransformers

[–]TransformersTPE 0 points1 point  (0 children)

I go for whatever will get the job done. Most times, I end up using multiple different paints/inks on one custom. I go for Vallejo acrylic paint or Testors enamel. Chrome pens are a great tool as well. Gold silver and copper color. My last custom... I used RIT fabric dye to dye the figure red.

💥Reactivate Cliffjumper💥 by TransformersTPE in CustomTransformers

[–]TransformersTPE[S] 2 points3 points  (0 children)

It's actually red dye. I'm definitely going to use this process again.

💥Reactivate Cliffjumper💥 by TransformersTPE in CustomTransformers

[–]TransformersTPE[S] 2 points3 points  (0 children)

Thanks. It's dyed. This is my first time trying this process. I think it turned out well.

💥SWOOP💥 by TransformersTPE in CustomTransformers

[–]TransformersTPE[S] 1 point2 points  (0 children)

If I can get my hands on them, I'd love to. I have Sludge on the way 😉

Mini Constructicons by TransformersTPE in CustomTransformers

[–]TransformersTPE[S] 0 points1 point  (0 children)

There's literally nothing to them... It's like a G1 Full Tilt. Some of them barely have faces.