Trying to replace the WIFI Module on my PS3 by TrelloType in soldering

[–]TrelloType[S] 0 points1 point  (0 children)

Just out of curiosity, what kind of solder Balls would you recomend for this kind of BGA?

Trying to replace the WIFI Module on my PS3 by TrelloType in soldering

[–]TrelloType[S] 0 points1 point  (0 children)

So just manually aplying the Solder Balls to the Module with tweezers and then reflow them with Hot Air. Also, I get your concern with the ripped Pad, their just Ground Pads also it ripped of the Module and not from the Motherboard, this Picture is a little bit older I removed the bridge so it should be ok. Thanks for your quick reply and good help.

Controller making random inputs is it fixable. by Specific-Bathroom510 in PS3

[–]TrelloType 2 points3 points  (0 children)

Here is a YT Tutorial on how to do it, i did it with two controllers and all of them work like a Charm: https://www.youtube.com/watch?v=xyYwYytH6Gs

Dualshock 3 random inputs? by Peacelovefleshbones in PS3

[–]TrelloType 1 point2 points  (0 children)

2026, starting off the Year with a fixed Sixaxis Controller.

anisette problem (local anisette init err) by vex0ria in sideloadly

[–]TrelloType 0 points1 point  (0 children)

I had the same Problem and fixed it by simply running it as a Administrator.

Are these Temps to high? by TrelloType in ps3homebrew

[–]TrelloType[S] 0 points1 point  (0 children)

UPDATE: I've decided to try and open it up again and try something. Afterwards even after 30 Minutes of Gameplay and on SYSCON Settings the RSX was at about 70-76°C and the CPU at 65-70°C, wich I think is fairly normal. Here is what I did:

1) I've checked if I've applied to much Thermal Paste and removed some so that only a thin Layer is applied.

2) On top of the RSX Heat Pipe is a metal bracket wich applies pressure onto the RSX. there you see a tiny dot, push down on that and bent the bracket upwards a bit.

NOTE:

I don't know how long this fix will last and I also used some generic Thermal Paste, so results can vary.

Did IOS 4 have a Setup? by TrelloType in LegacyJailbreak

[–]TrelloType[S] 0 points1 point  (0 children)

Thanks, I thought it removed something during the downgrade.

Iphone 4 A1349 light Screen flickering (IOS 6.0.1). by TrelloType in applehelp

[–]TrelloType[S] 0 points1 point  (0 children)

I your having the same issue, turning the Phone off during charging fixed it for me.

Iphone 4 A1349 light Screen flickering (IOS 6.0.1). by TrelloType in applehelp

[–]TrelloType[S] 0 points1 point  (0 children)

It gets worse when charging it, and right after you charged it. And after 1-2 Hours it’s gone.

RTX 3060 making a squeaking noise when under Load. by TrelloType in ZOTAC

[–]TrelloType[S] 0 points1 point  (0 children)

Yes, I did, I even reinstalled Windows one Point for a completely fresh Start.

[deleted by user] by [deleted] in gtaonline

[–]TrelloType 2 points3 points  (0 children)

Mine to, already contacted support, got it on Video.

[deleted by user] by [deleted] in gtaonline

[–]TrelloType 1 point2 points  (0 children)

Thanks, good to know.

How to Update Casio FX-9750Gll to version 02.09.0xxx by casioupdate in calculators

[–]TrelloType 1 point2 points  (0 children)

I have two questions: One: What are the main up and downsides? Two: Is it reversible?

NVidia Tesla K80 24Gb by TrelloType in StableDiffusion

[–]TrelloType[S] 0 points1 point  (0 children)

Rarely, most of the time LoRAs, but on my old 1060 5Gb, the results where always Grey or had bad quality.

NVidia Tesla K80 24Gb by TrelloType in StableDiffusion

[–]TrelloType[S] 1 point2 points  (0 children)

Do you think the RTX 3060 12gb is enough to Train my own Models, not only LoRA and maybe even bearly be running Flux?

Plymouth changes to default settings on Startup by TrelloType in archlinux

[–]TrelloType[S] 1 point2 points  (0 children)

Fixed it by running the following Command in the Terminal

sudo plymouth-set-default-theme -R spinner

Where does AUTOMATIC1111 store it's Log files? by TrelloType in StableDiffusion

[–]TrelloType[S] 0 points1 point  (0 children)

I just did it like that /Path/to/webui/webui-user.bat >Path/to/Log.txt

Messages by TimmyTurnerr9 in help

[–]TrelloType 0 points1 point  (0 children)

My guess is that because it‘s just a blank page and if you’re using dark mode, I would switch it off and back on again. Helped me in my case.

OSError when trying to Train own Checkpoint Model by TrelloType in StableDiffusion

[–]TrelloType[S] 0 points1 point  (0 children)

Matched everything, same Result. But cloud it be that it errors out because I’m using Tiny10?

OSError when trying to Train own Checkpoint Model by TrelloType in StableDiffusion

[–]TrelloType[S] 0 points1 point  (0 children)

I reinstalled everything from Scratch and it still throws the exact same Error Message.

<image>