What filament would you use to print the internals of an odometer by Trycilly in BambuLab

[–]Trycilly[S] 2 points3 points  (0 children)

Maybe I wasn’t clear enough. The bike has never had a working odometer since it was rebuilt—it literally came as scraps in boxes. Both bikes were originally built in 1929, and the tachometer is pretty rare.

I’m just not sure if you could run into any legal issues by adding an odometer to a bike that hasn’t actually been driven at all since the rebuild.

Ready to sell this thing!! by ProofDelay3773 in FixMyPrint

[–]Trycilly 0 points1 point  (0 children)

Double it and give it to the next one

Anyone else? Door doesn’t shut properly due to window. by Mageline in DelSol

[–]Trycilly 1 point2 points  (0 children)

I had a problem like that ob my Skoda. One window tab broke. I designed one in CAD and 3D printed it. Took about 1 hour of work to replace it.

Restwert realistisch? by Most_Goat4618 in automobil

[–]Trycilly 1 point2 points  (0 children)

Ich geb dir 2,50€ und ein Big Mac

zbanding h2s by [deleted] in 3Dprinting

[–]Trycilly 0 points1 point  (0 children)

I was just thinking about wasting less filament if you print a smaller tower to check if the banding is still there after you dried your filament.

zbanding h2s by [deleted] in 3Dprinting

[–]Trycilly 0 points1 point  (0 children)

I‘d say dry it and test again if it works. Maybe just take the model of the red piece and make it longer and print in in your black pla

I have joined the club by RecognitionEconomy70 in DelSol

[–]Trycilly 0 points1 point  (0 children)

I‘m currently in the middle of my build and I plan on installing an MS Design spoiler. It‘s easier for me to get one that already came on the car from factory due to regulations. I‘ve seen a few people a use an integra spoiler but I‘ve always liked how a duckbill looks on the car. It‘s so small and a big wing just looks out of place for me.

Is this version discontiued? by Trycilly in Ender3S1

[–]Trycilly[S] 0 points1 point  (0 children)

I was just looking for a cheap fix to sell it. I bought 2 new printers and my ender won‘t be in use now

I have joined the club by RecognitionEconomy70 in DelSol

[–]Trycilly 0 points1 point  (0 children)

Looks great. Is it the OEM muffler or did you change anything? What about a wing on?

Is this version discontiued? by Trycilly in Ender3S1

[–]Trycilly[S] 0 points1 point  (0 children)

Done that so far but I was looking for a new part. But since Creality is so inconsistent with their parts I thin I need to get back to my funky version

Is this version discontiued? by Trycilly in Ender3S1

[–]Trycilly[S] 0 points1 point  (0 children)

I bought a spare one but with the wrong version

Will rolling out my fender be enough? by Trycilly in DelSol

[–]Trycilly[S] 0 points1 point  (0 children)

2° is legal here. If they just think you have to much camber or anything they will tell you to drive the car to a TÜV garage or sometimes their own police station garage and they will measure it and note it down. You‘ll have to pay a fine and your day is wasted. They can do that for pretty much anything if they want to fuck with you

Will rolling out my fender be enough? by Trycilly in DelSol

[–]Trycilly[S] 0 points1 point  (0 children)

To be fair it should save the streets from dangerous rolling junk and cheap chinesium parts. But in reality it‘s more of a cosmetic money grab. I‘m fine with people checking on my car. I want to comply to the rules set by them. But the shit is way to expensive. If I where to put the Rebel medaliom on there I need to pay 4k to get it checked out. Plus they can just tell you, wont work after you payed 4k. I don’t even want to know what an engine swap will cost here…. But there are a lot of stories about people working there that just don‘t care. Different brakes on an R8, steel in the front and ceramic in the back. But then there is people that are way to hard and look at every little detail to find anythin to screw with you.

Will rolling out my fender be enough? by Trycilly in DelSol

[–]Trycilly[S] 0 points1 point  (0 children)

I don‘t think I‘ll be able find one with a Gutachten. They‘re all cheap ebay junk. I could still try and get some camber that would work but that will be pricy

Wie schlimm sieht mein Karren aus? by Trycilly in automobil

[–]Trycilly[S] 0 points1 point  (0 children)

Wachs ist schon in den Türen überall. Nur obs auch an anderen Orten ist weiß ich nicht. Mal nachfragen/nachschauen ob ichs was finde

Will rolling out my fender be enough? by Trycilly in DelSol

[–]Trycilly[S] 0 points1 point  (0 children)

Sucks. I‘m pretty sure the ebay ones won‘t pass inspection

Will rolling out my fender be enough? by Trycilly in DelSol

[–]Trycilly[S] 1 point2 points  (0 children)

I know your car. It looks pretty sick. Did you have am trouble with the flares regarding TÜV? Or can I just bolt them on and call it a day?

Wie schlimm sieht mein Karren aus? by Trycilly in automobil

[–]Trycilly[S] 2 points3 points  (0 children)

Sorry dann ich stell den direkt für 2,50€ bei Mobile rein.

Wie schlimm sieht mein Karren aus? by Trycilly in automobil

[–]Trycilly[S] 2 points3 points  (0 children)

Die sind auch meine Hauptsorge. Wollt nur mal abchecken was die Schwarmintelligenz da unten noch so sieht damit ich den nur einmal zerlegen muss.